manualshive.com logo in svg

Radyne OM20, Installation And Operation Manual

Share
Download
Radyne OM20 Installation And Operation Manual Download Page 175

MN-OM20– Revision 5 

D–1 

Appendix D.  Quick Start Guide 

D.1 

Introduction 

This section provides quick setup instructions to access the Web Browser through the RJ45 
Ethernet interface.  The Web user interface allows for complete monitoring and control of all 
modem parameters and functions via a 10BaseT Ethernet connection.  For more details on the 
various WEB configurations and a description of all the available selections, please refer to the 
manuals.   

D.2 

Required Items 

 

Modem 

 

RJ45 to RJ45 cable 

 

Computer 

 

Default Plug (J2) 

 

 

IMPORTANT

 

The Web Browser menus for the OM20 can only be accessed utilizing  

Microsoft Internet Explorer 6 or greater. 

 

D.3 

Web Interface Setup Guidelines 

D.3.1  Preparing the OM-20 for Web Setup  

The unit is shipped from the factory with specific IP defaults.  The factory defaults are set to an 
unreachable state to minimize any adverse effects to the user’s network.  In order for the user to 
change the IP addresses to an accessible address the user must first install the Reset Plug onto J2 
that is supplied with the unit.  This will change the IP network setting that the user can access.     

Summary of Contents for OM20





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands