manualshive.com logo in svg

Radyne OM20, Installation And Operation Manual

Share
Download
Radyne OM20 Installation And Operation Manual Download Page 23

OM20 Universal Outdoor Modem 

Installation 

MN-OM20– Revision 5 

2–3 

2.3

 

Removal and Assembly 

The Standard OM20 is shipped in a single box that contains mating connectors.  Carefully unpack 
the unit and ensure that all of the above items are in the carton. The standard OM20 power supply 
is designed for universal AC (95-250VAC, 50/60 Hz) application and is capable of supplying DC 
power to the BUC and LNB.  See the specification section of this document for appropriate 
voltages and currents.  Optionally, a -48VDC power supply may be specified for the unit. 
 

CAUTION

 

Always ensure that power is removed from the OM20 before removing or 
installing the BUC or LNB.  Failure  to do so may cause damage to the 
equipment.

 

 

 

 

 

Figure 2.2. OM 20 Front Interconnects 

 
 

Summary of Contents for OM20





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands