manualshive.com logo in svg

Radyne OM20, Installation And Operation Manual

The New Rock Technologies OM20 is a cutting-edge communication device designed to streamline your connectivity. The Quick Installation Manual provides step-by-step instructions for hassle-free setup. Download this manual for free at manualshive.com to unlock the full potential of your OM20 and enhance your communication experience.

Share
Download
background image

MN-OM20– Revision 5 

5–1 

Chapter 5.

 

Rear Panel Interfaces 

This section discusses the electrical interfaces available of the unit.   

5.1

 

OM20 External Interface Connections 

All OM20 external connections are interconnected to labeled connectors located on the front of 
the unit.  Any connection interfacing to the OM20 must utilize the appropriate mating connector 
(supplied).  Refer to Table 5.1 and Figure 5-1 for the standard unit. Reference throughout this 
section will be identified as the OM20. 
 

LABELS 

J1 Power 

J2 232/485 M&C/Terminal 

J3 EIA-530 Data I/O / ES-ES Data/ Balanced G.703 

J4 Ethernet (Data/M&C) 

J6 Ground 

J7 RX L-Band Input 

J8 TX L-Band Output 

J9 Compact Flash Card 

J10 SD G.703 (DDI) Unbalanced, Optional ASI 

J11 RD G.703 (IDO) Unbalanced, Optional ASI 

J12 External Clock BNC  

Table 5-1 OM20 Connection Designations 

 

Summary of Contents for OM20





























































































































































































































Reviews:

No comments

Related manuals for OM20

ADC MM300S Installation Manual preview
MM300S
Brand: ADC Pages: 7
USR IOT USR-G771-E User Manual preview
USR-G771-E
Brand: USR IOT Pages: 31
Ebyte E96-DTU User Manual preview
E96-DTU
Brand: Ebyte Pages: 22
Ovation MC679 Quick Start Manual preview
MC679
Brand: Ovation Pages: 19
Patton electronics 1088/I User Manual preview
1088/I
Brand: Patton electronics Pages: 13
Motorola MB7420 Quick Start Manual preview
MB7420
Brand: Motorola Pages: 12
TP-Link TD-W8960N Installation Manual preview
TD-W8960N
Brand: TP-Link Pages: 24
Phason MDM-GSM Installation Manual preview
MDM-GSM
Brand: Phason Pages: 4
ComBlock COM-1503 Manual preview
COM-1503
Brand: ComBlock Pages: 22
Datatronics ITU-T V.42bis Getting Started Manual preview
ITU-T V.42bis
Brand: Datatronics Pages: 22
Adeunis RF ARF45 User Manual preview
ARF45
Brand: Adeunis RF Pages: 27
Adeunis RF ARF7883AA User Manual preview
ARF7883AA
Brand: Adeunis RF Pages: 50
Fritz! AC430 MU-MIMO Configuration And Operation preview
AC430 MU-MIMO
Brand: Fritz! Pages: 44
Fritz! Box 3272 Installation And Operation Manual preview
Box 3272
Brand: Fritz! Pages: 137
Converters.TV 524 Operation Manual preview
524
Brand: Converters.TV Pages: 7
Lucent Technologies CellPipe 20A-USB User Manual preview
CellPipe 20A-USB
Brand: Lucent Technologies Pages: 44
Raisecom RC801-60B-FV35 Series User Manual preview
RC801-60B-FV35 Series
Brand: Raisecom Pages: 30
Zte MF190A Quick Manual preview
MF190A
Brand: Zte Pages: 9

Brands by name

Popular brands

Load more brands