manualshive.com logo in svg

Radyne OM20, Installation And Operation Manual

The New Rock Technologies OM20 is a cutting-edge communication device designed to streamline your connectivity. The Quick Installation Manual provides step-by-step instructions for hassle-free setup. Download this manual for free at manualshive.com to unlock the full potential of your OM20 and enhance your communication experience.

Share
Download
background image

OM20 Universal Outdoor Modem 

Web Browser/Remote Protocol 

 

MN-OM20– Revision 5 

6–33 

 
 

 

 

Data Rate (bps): 

{Refer to Technical Specs for Data Rates} 

 

Allows the user to set the Data Rate in bps steps via the Front 
Panel Arrows or Keypad. 

 
 

Symbol Rate (sps):

 

Allows the user to view the Symbol Rate. 

 

 

INNER FEC 

Viterbi  

 

{1/2, 3/4, 7/8, None} 

 

 

Optional FEC Rates:  

 

 

Sequential 

 

{1/2, 3/4, 7/8}  

 

 

Trellis  8PSK   

{2/3} 

 

 

Turbo 

≤ 5 Mbps 

{.793, .495} 

 

 

Turbo 

≤ 20Mbps 

{1/2, 3/4, 7/8} 

 

 

Comstream Seq 

{3/4} 

 

 

DVB VIT 

 

{1/2, 2/3, 3/4, 5/6, 7/8} 

 

 

DVB Trellis 

 

{2/3, 5/6, 8/9} 

 
 

Allows the user to select the Rx Code Rate and Type. 

 
 

TPC Interleaver 

{DISABLED, ENABLED} 

 

 

 

Allows the user to disable or enable TPC Interleaver. Valid only 
for Radyne turbo codes TPC.495 and TPC.793. 

 

 

Differential Encoding 

{ENABLED, DISABLE} 

 

 

 

Allows the user to enable or disable the Differential Decoder. 
Having the decoder enabled ensures proper phase lock.  May not 
be adjustable in some modes. 

 

Scrambler Selection

 

{NONE, V.35-IESS, V.35 CITT, V.35 EF, IBS w/Optional 
Framing and optional Reed-Solomon, Reed-Solomon 
Scrambler w/Optional Framing, CCITT, V.35FC, OM-73, 
V.35EF_RS, TPC, DVB, EDMAC}

 

 

 

 

Allows the user to select the descrambler type. 

 
 

Scrambler Control 

{ON, OFF} 

 

 

 

Allows the user to enable or disable the descrambler operation. 

 

 

Satellite Framing

 

{1/15 (IBS), 1/15 (Async), 96 Kbps (IDR), EDMAC, 
EFAUPC, SCC, None}

 

 

Used with IDR, IBS, or Asynchronous Interface Only. 

 

Allows the user to select the Framing Type. 

 
 

Terrestrial Framing

 

{NONE, 188, 204} DVB only 

 

 

 

Allows the user to select the Receive Terrestrial Framing. 

 
 

Data Polarity

 

{INV. TERR & BASE, INV. BASEBAND, INV.TERR 
DATA, NONE}

 

 

Allows the user to invert the Rx Data polarity. 

 
 

Symbol Pair: 

Symbol Pair:  {NONE, SWAPPED} 

 

Allows the user to swap the I & Q Channels. 

Summary of Contents for OM20





























































































































































































































Reviews:

No comments

Related manuals for OM20

Panasonic Digital Business System Installation Manual preview
Digital Business System
Brand: Panasonic Pages: 58
Teracom T2-B-Gawv1.4U10Y-BI User Manual preview
T2-B-Gawv1.4U10Y-BI
Brand: Teracom Pages: 131
Lava PAYLINK-IP/232 Configuration Manual preview
PAYLINK-IP/232
Brand: Lava Pages: 27
Hercules HWGUm-54 Quick Start Manual preview
HWGUm-54
Brand: Hercules Pages: 6
Ebyte E830 Series User Manual preview
E830 Series
Brand: Ebyte Pages: 20
Ebyte E821-RTU User Manual preview
E821-RTU
Brand: Ebyte Pages: 29
Carel Sierra AirLink FXT Series Installation Manual preview
Sierra AirLink FXT Series
Brand: Carel Pages: 2
Telstra TURBO Getting Started Manual preview
TURBO
Brand: Telstra Pages: 20
US Robotics 005689-03 Manual preview
005689-03
Brand: US Robotics Pages: 68
Four-Faith F8914-E User Manual preview
F8914-E
Brand: Four-Faith Pages: 26
Triz TZ3200C User Manual preview
TZ3200C
Brand: Triz Pages: 22
GaneData I-DEM 16 User Manual And Manual preview
I-DEM 16
Brand: GaneData Pages: 14
Ebyte EBT3001 User Manual preview
EBT3001
Brand: Ebyte Pages: 29
D-Link Ultra Performace Series Quick Installation Manual preview
Ultra Performace Series
Brand: D-Link Pages: 32
Ebyte E62-DTU (433D30) User Manual preview
E62-DTU (433D30)
Brand: Ebyte Pages: 16
Ebyte E800-DTU V8 Series User Manual preview
E800-DTU V8 Series
Brand: Ebyte Pages: 17
Ebyte E32-DTU User Manual preview
E32-DTU
Brand: Ebyte Pages: 22
Ebyte 900SL30-GPRS User Manual preview
900SL30-GPRS
Brand: Ebyte Pages: 22

Brands by name

Popular brands

Load more brands