manualshive.com logo in svg

Radyne OM20, Installation And Operation Manual

Share
Download
Radyne OM20 Installation And Operation Manual Download Page 167

MN-OM20– Revision 5 

B–1 

Appendix B.  Software Upgrade 

Procedure 

The outdoor modem software may be upgraded via the terminal or the web interface. 

B.1 

Terminal Software Upgrade 

The OM20 Outdoor Modem offers the ability to perform field upgrades of the modem’s feature 
set quickly and easily from the Terminal Port.  Purchased upgrades will become part of the 
modems permanent configuration.  Demonstration upgrades will enable the optional features for 
a 30-day evaluation period. 

B.2 

Required Equipment 

The OM20 Universal Satellite Modem is the only equipment required for this procedure. 

B.3 

Upgrade Procedure 

The following paragraphs describe the procedure for permanently updating the feature set of the 
OM20 Universal Satellite Modem  
 

1.

 

The following steps allow users to quickly determine from the GUI Interface whether or 
not the desired feature(s) are supported by the hardware currently installed in the 
modem. 

 
Using the GUI interface navigate to the Features menu under “System” gel-tab. Click on 
“features”.  This will show the available features and all features checked are the 
purchased/installed features. 
 

2.

 

Contact Comtech EF Data Customer Service with the Unit ID and Desired Upgrades.  
The modem’s Unit ID can be found in the Terminal interface as follows: 

 

a.

 

From the main menu, the Features menu. 

b.

 

“Feature Id: is the unit ID number 

Summary of Contents for OM20





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands