manualshive.com logo in svg

Radyne OM20, Installation And Operation Manual

Share
Download
Radyne OM20 Installation And Operation Manual Download Page 102

OM20 Universal Outdoor Modem 

Web Browser/Remote Protocol 

 

MN-OM20– Revision 5 

6–28 

 

 

 

AUPC MODE 

{DISABLE,NEAR SIDE, EFDATA} 

 

 

Allows the user to enable or disable the AUPC Function of the remote modem.  The remote AUPC Function is the 

response of the local modem to commands for an increase or decrease of the Transmit Power in 0.5 dB steps and the command to change to 
the setting indicated in the 'REMOTE CL ACTION' Menu of the remote modem upon receiver loss of lock. 

 
 

LOOPBACK 

{DISABLE, ENABLE} 

 

 

Allows the user to enable or disable the Baseband Loopback Test 
Mode of the remote modem. 

 

 

 

TX 2047 TEST 

{DISABLE, ENABLE} 

 

 

Allows the user to enable or disable the Transmit 2047 Pattern 
Test Mode of the remote modem.  

 

 

RX 2047 BER: 

Reports the BER measurement of the receiver 2047 Pattern Test 
Mode of the remote modem.  BER is reported from the 1x10

-5

 to 

1x10

-7

 in tenth decade steps.   

 

 

if the pattern does not synchronize or is out of range, ‘NO 
DATA’ will be displayed.  

 

IMPORTANT

 

When modems are configured for Radyne AUPC, the remote Eb/No will be 
displayed in the Monitor Menus.  

 

 

 

 

Summary of Contents for OM20





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands