manualshive.com logo in svg

Radyne OM20, Installation And Operation Manual

Share
Download
Radyne OM20 Installation And Operation Manual Download Page 96

OM20 Universal Outdoor Modem 

Web Browser/Remote Protocol 

 

MN-OM20– Revision 5 

6–22 

 
ODU BUC Menu 

 

 

 

Figure 6-12. OBU-BUC menu 

 

 

LO Frequency (MHz):

 

Allows the user to enter the Local Oscillator frequency of the 
BUC LO in order for the uplink frequency to be displayed 
correctly (refer to the BUC manufacturer’s specifications).   

 

  

 

 

 

NOTE:  When utilizing BUC that supports  

 

  

 

 

FSK, the modem will display LO frequency  

 

 

  

 

as stated by the BUC.

 

 
 
 

Carrier Delay (sec): 

{0 to 255} 

 

Allows the user to select the time delay after power-up before 
the Tx Carrier may be enabled.  This allows time for the BUC to 
stabilize. 

 
 
 

OSC Side Band: 

{LOW SIDEBAND, HIGH SIDEBAND} 

 

Allows the user to select the location of the BUC LO.  The user 
must enter the location of the BUC LO in order for the UPLINK 
FREQUENCY to be displayed correctly.  The BUC LO can be 
either higher or lower in frequency than the BUC output 

Summary of Contents for OM20





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands