manualshive.com logo in svg

Radyne OM20, Installation And Operation Manual

The New Rock Technologies OM20 is a cutting-edge communication device designed to streamline your connectivity. The Quick Installation Manual provides step-by-step instructions for hassle-free setup. Download this manual for free at manualshive.com to unlock the full potential of your OM20 and enhance your communication experience.

Share
Download
background image

OM20 Universal Outdoor Modem 

Web Browser/Remote Protocol 

 

MN-OM20– Revision 5 

6–50 

solid indication points toward a problem with the incoming clock 
to the modem (SCTE). 

 
 

LB Synth PLL: 

{Pass/Fail, Unmasked/Masked} 

Indicates that the Tx L-Band Synthesizer is not locked.  This 
alarm will flash on during certain modem parameter changes.  A 
solid indication points toward a configuration problem within the 
modem. 

 
 

 

 

BUC Current:

 

{Pass/Fail, Unmasked/Masked} 

 

 

 

Indicates that current is either below or above the threshold 
limits of the BUC, as specified by the OM20.  Only active when 
BUC Voltage is enabled 

 

 

BUC Voltage:

 

{Pass/Fail, Unmasked/Masked} 

 

 

 

Indicates that the voltage is not functioning correctly when the 
BUC Voltage is enabled. 

 
 

Ethernet WAN 

{Pass/Fail, Unmasked/Masked} 

 

 

 

Indicates that the interface card is faulted and will not pass data 

(displays only when the Ethernet Card is installed and the 
Ethernet Interface is selected). 

MINOR ALARMS

 

 
 

Terr Clock Act: 

{Pass/Fail, Unmasked/Masked} 

 

Indicates no Terrestrial Clock activity. 

 
 

Terr Data Act: 

{Pass/Fail, Unmasked/Masked} 

 

Indicates no Tx Data activity. 

 
 

Terr AIS:   

{Pass/Fail, Unmasked/Masked} 

 

Indicates that AIS has been detected in the Tx Data Stream. 

 
 

DnI Frame Lock: 

{Pass/Fail, Unmasked/Masked} 

 

Indicates that the TX Oversample Clock PLL is not locked.  This 
alarm will flash on during certain modem parameter changes.  A 
solid indication points toward a configuration problem within the 
modem. 

 

 

 

DnI MFrame Lock: 

{Pass/Fail, Unmasked/Masked} 

 

Indicates that Tx Composite Clock PLL is not locked.  This 
alarm will flash on during certain modem parameter changes.  A 
solid indication points toward a problem with the incoming clock 
to the modem (SCTE). 

 
 

DVB Frame Lock: 

{Pass/Fail, Unmasked/Masked} 

 

Indicates that Tx input data stream framing does not match the 
user selected TX TERR FRAMING. 

 
RESET LATCHED ALARMS: 

Clicking on this button will reset (Clear) all Latched Alarms 

 

Summary of Contents for OM20





























































































































































































































Reviews:

No comments

Related manuals for OM20

Abocom FM560C Quick Installation Manual preview
FM560C
Brand: Abocom Pages: 14
Linksys ADSLME1 User Manual preview
ADSLME1
Brand: Linksys Pages: 12
Patton electronics 1070RC User Manual preview
1070RC
Brand: Patton electronics Pages: 28
Maxon MA-2020 User Manual preview
MA-2020
Brand: Maxon Pages: 100
Exede RM5110 Series Warranty, Safety, And Environmental Information preview
RM5110 Series
Brand: Exede Pages: 4
Comtech EF Data CDM-550 Application Note preview
CDM-550
Brand: Comtech EF Data Pages: 5
Comtech EF Data CDM-710 Installation And Operation Manual preview
CDM-710
Brand: Comtech EF Data Pages: 242
Conceptronic C54WIFIU Quick Installation Manual preview
C54WIFIU
Brand: Conceptronic Pages: 105
Zte IX380 User Manual preview
IX380
Brand: Zte Pages: 68
Raymar 3460 User Manual preview
3460
Brand: Raymar Pages: 171
Raymar Alliance V.32 Instruction Manual preview
Alliance V.32
Brand: Raymar Pages: 201
Ebyte E90-DTU Manual preview
E90-DTU
Brand: Ebyte Pages: 35
NETGEAR CM500V User Manual preview
CM500V
Brand: NETGEAR Pages: 30
Fritz! Fritz!Box 5530 Manual preview
Fritz!Box 5530
Brand: Fritz! Pages: 250
Speed Touch 330 Installation Manual preview
330
Brand: Speed Touch Pages: 6
Geetel INTERNET DSL MODEMS Handbook preview
INTERNET DSL MODEMS
Brand: Geetel Pages: 10
Archtek 5634PCV User Manual preview
5634PCV
Brand: Archtek Pages: 38
Hughes HN9800 User Manual preview
HN9800
Brand: Hughes Pages: 34

Brands by name

Popular brands

Load more brands