Radyne OM20 Installation And Operation Manual Download Page 118

Page: 118 / 220

OM20 Universal Outdoor Modem

Web Browser/Remote Protocol

MN-OM20– Revision 5

6–44

6.3.4.4

Monitor Menu

General | Voltages Menu

Figure 4-21. General | Voltages Menu

IMPORTANT

LNB and BUC options are only available on the

DMD20LBST and the OM20.

Rx Offset Frequency (Hz):

Displays the received carrier frequency offset as measured by the
modem.

Rx Input Level (dBm):

Displays the estimated receive signal level as seen by the
Demodulator. This window is active continuously and is above
the Gel Tab area.

Eb/No (dB):

Displays the estimated E

as seen by the demodulator. This

window is active continuously and is above the Gel Tab area.

Raw BER:

Displays the estimated channel error rate (before decoding)
measured by the modem. This window is active continuously
and is above the Gel Tab area.

Summary of Contents for OM20





























































































































































































































Search results

Summary of Contents for OM20

Reviews:

Brands by name

Popular brands

Radyne OM20, Installation And Operation Manual

Search results

Summary of Contents for OM20

Reviews:

Brands by name

Popular brands