manualshive.com logo in svg

Radyne OM20, Installation And Operation Manual

Share
Download
Radyne OM20 Installation And Operation Manual Download Page 176

OM20 Universal Outdoor Modem 

Appendix D 

MN-OM20– Revision 5 

D–2 

 

1.

 

Turn off power to the OM-20.   
 

2.

 

Install the Reset mating connector on J2 port. 
 

3.

 

Turn on power to the OM-20 and allow it to run for 2 minutes. 
 

4.

 

Turn off power to OM-20 and remover the Reset mating connector from J2. 
 

5.

 

The IP addresses of the OM-20 are now configured to the following: 

 

Boot Modes:

     

IPTEST 

 

 

Bootp Server Tag: 

206 

 

 

IP Address Mask: 

255.255.255.000 

 

 

 

Modem IP Address: 

192.168.0.238   

 

 

 

Server IP Address: 

192.168.000.101 

 

 

 

Router IP Address:   

192.168.000.102 

 

 

6.

 

In order for the computer to recognize the modem, the computers subnet Mask must match the 
Subnet Mask of the modem. The IP Address Mask is 255.255.255.000.  To ensure the safety of 
the network, it may be necessary to contact the network administrator.   
   

7.

 

Turn on the unit.  The unit is now ready to connect to the computer.  Connect the RJ45 cable 
from the OM-20 to the computer/router/bridge as illustrated in Figure 1. 
 

 

 

Figure 1.  Ethernet Connection 

 

8.

 

Initiate PING test to ensure there is communication between the modem and the computer  
 
Example: ping 192.168.0.238  
 
If everything is functioning correctly, replies from the modem will appear on the computer 
screen along with the time it took to respond.  If unsuccessful, verify the following: 

 

Summary of Contents for OM20





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands