Owner’s Manual
400-051-202-01 Rev. B
Page 4-11
Chain Lift Control Box Operation/Troubleshooting
The chain lift is also powered by a chain lift control box (P/N 051-200-299-XX),
independent from the Odd and Even machine control boxes. This unit powers the chain
lift drive motor and the ball detection sensors. It also handles all communication tasks
between these subsystems and the system controller. The following chart outlines the
functionality of the control board LED indicators during various operating conditions.
GREEN
- Always ON when power is applied
YELLOW
– Normally OFF
Flashing
RED
- Normally ON; OFF when ball is detected
ON
ON
RED
- Always ON when power is applied
ON
OFF
RED
- Always ON when power is applied
ON
ON
RED
- Always ON when power is applied
OFF
OFF
Normally OFF
OFF
ON
Normally OFF
OFF
OFF
Normally OFF
OFF
ON
Normally OFF
ON
OFF
Normally OFF
ON
ON
RED
- On when lanes are in BOWL mode
ON
OFF
OFF when lanes are in STANDBY mode
Machine control box not properly grounded.
Machine control box internal communication failure.
The number of flashes indicates a specific drive error. Error will also display on the system controller.
LED 6 Flashing - BALL LIFT IS WAITING FOR COMM – Waiting for communications from the system
controller. Once communication is established, it will then begin calibration.
LED 6 & 7 Flashing – BALL LIFT IS CALIBRATING – Calibration attempt in progress. Once calibrated,
these LED’s turn off.
LED 6, 7 & 8 Flashing – BALL LIFT IS IN SAFE MODE – Calibrations failed. Must power cycle to correct.
Summary of Contents for Edge String
