Owner’s Manual
400-051-202-01 Rev. B
Page E-20
Precautions:
LOTO, Lane Barriers, Slip Hazard
Tools:
•
Ratchet or Impact Driver
•
7
/
16
” and ½” Sockets
•
7
/
16
” and ½” Wrenches
•
#2 Phillips Screwdriver
•
Chain Lift Service Lock (051-200-532)
Location:
Operator Access Area (behind machine), Pit
Est. Time:
90 min
Note:
•
The estimated time assumes an impact driver is used.
Procedure:
1.
Implement LOTO and deploy lane barriers.
2.
Remove pit rear guards (both pits) and double division guard.
3.
Remove ball rails, ball stop, and support bracket.
4.
Remove system controller guard.
5.
Disconnect chain lift gearmotor cable from chain lift control box.
6.
Remove chain lift ground wire from chain lift control box.
7.
Remove bolts (2) from gearmotor mounting plate and remove chain
lift gearmotor.
8.
Install chain lift service lock (051-200-532). See Figure E-18.
9.
Remove chain lift guarding.
10.
Loosen nut and bolt connecting system controller wireway to cross
machine wireway. Do not remove hardware.
11.
Remove system controller from its mount and set aside.
a.
System controller cables do not need to be unplugged. Place
system controller on pit hinged top cover of even machine.
12.
Remove system controller mount.
13.
Wrap ground wire around gearmotor mount.
14.
Remove bolts (2) attaching cross sweep to top of chain
lift. Support chain lift as needed.
15.
Lift up on chain lift to slide it off foundation posts (2).
16.
Carefully carry or slide chain lift out from between pit
side frames.
a.
If chain is stuck or caught on something, do not
pull. Free any obstruction first.
b.
Use caution to avoid damaging chain lift ball
sensors and cables.
17.
Follow above steps in reverse order to install chain lift.
18.
Remove LOTO and lane barriers. Return machine to service.
Figure E-17, Chain Lift
Figure E-18, Chain Lift
Service Lock
Summary of Contents for Edge String
