Owner’s Manual
400-051-202-01 Rev. B
Page 4-10
Machine Control Box Operation/Troubleshooting
Each pinspotter is powered by a machine control box (P/N 051-200-299-XX). This unit
powers all pinspotter subsystems including the drawbar motor, string brake/encoder
boards, and tangle switch emitter board. It also handles all communication tasks between
these subsystems and the system controller. The following chart outlines the
functionality of the control board LED indicators during various operating conditions.
Machine Control Box (051-200-299-XX) LED Indicators
GREEN
- Always ON when power is applied
YELLOW
Flashing
ON
Flashing
OFF
ON
Flashing
ON
ON
Flashing
OFF
ON
Flashing
ON
OFF
Flashing
OFF
ON
Flashing
ON
ON
Flashing
OFF
ON
Flashing
OFF
OFF
Flashing
OFF
ON
Flashing
OFF
ON
Flashing
OFF
ON
Flashing
OFF
OFF
Flashing
OFF
ON
Flashing
OFF
ON
Flashing
OFF
ON
Flashing
ON
OFF
Flashing
OFF
ON
Flashing
ON
ON
Flashing
OFF
ON
Flashing
ON
OFF
Flashing as the strings move during
normal bowling play.
# of LEDs
illuminated indicates
string adjustment
quality
All LEDs OFF after string
adjust indicates string
adjustment is correct.
LED(s)
solid
ON indicates
corresponding string(s) too loose.
LED(s)
blinking
ON indicates corresponding
string(s) too tight. Adjust immediately.
Machine control box not properly grounded.
Machine control box internal
communication failure
The number of flashes indicates a specific drive error.
Error will also display on the system controller.
Steady ON indicates a string tangle.
Summary of Contents for Edge String
