3M
™
Speedglas
™
Welding Helmet 9100 FX Air
To optimise the effective lifetime of your welding equipment and avoid the additional cost of replacement, regular
maintenance is important. Replace all damaged parts immediately to ensure correct levels of protection.
• Helmet and head harness. Inspect for cracks or
any damaged or defective parts. Replace if needed.
• Cover lenses and visor. To provide the best possible vision
they should be clean and without scratches.
• Face seal. If the face seal is damaged there is a great
risk that contaminated air will get inside the helmet.
Verify it’s in position and free from splits and tears.
• Welding lens. Ensure low battery is not flashing
and check that the sensors are clean and uncovered.
• Breathing tube. Confirm tube is not damaged or
leaking any air. To extend the life of breathing tube,
use a tube cover or a heavy-duty rubber tube.
Before use
After use
• Clean the helmet. Wipe with a moist tissue or cloth, both inside and
outside the helmet. If you suspect that the inside of the airduct is dirty,
it must be changed.
DO NOT rinse, immerse in water or clean with solvents.
• Face seal and sweatband. Remove for additional cleaning
as needed and replace if they become unhygienic.
• Cover lenses and visor plate. Clean with a soft cloth
and replace if any pits or scratches occur.
• Breathing tube. Replace if damaged, deformed or leaking any air.
• Storage. Store the helmet in a dry, clean area away from direct
sunlight, high temperatures and solvents.
54 28 00
53 10 00
42 20 00
16 91 00
52 80 25
50 00 26
52 60 00
52 70 00
52 70 70
16 90 10
16 90 07
17 10 20
17 10 21
17 10 22
17 10 23
17 10 24
16 90 06
53 61 00
53 62 00
53 60 00
53 30 00
53 50 00
53 35 00
52 30 00
52 30 01
54 05 00
53 20 16
53 40 00
Care & Maintenance
171020
171021
171022
171023
171024
422000
500026
523000
523001
526000
527000
527070
528025
531000
532016
533000
533500
533505
534000
535000
536000
536100
536200
540500
542800
790101
HEAD COVER SMALL 9100 FX
HEAD COVER LARGE 9100 FX
THROAT PROTECTION 9100
HEAD CAPE TECAWELD
SWEATBAND 9100 & 9100 FX PK=2
SWEATBAND 9100 & 9100 FX PK=5
SWEATBAND 9100 & 9100 FX PK=50
LENS MAGNIFYING 1.0X 9100 100 & 9000
LENS MAGNIFYING 1.5X 9100 100 & 9000
LENS MAGNIFYING 2.0X 9100 100 & 9000
LENS MAGNIFYING 2.5X 9100 100 & 9000
LENS MAGNIFYING 3.0X 9100 100 & 9000
BATTERY LITHIUM 9100, 100 & 9000 PK=2
LENS WELDING 9100XXi SPEEDGLAS
VISOR PLATE 9100 FX PK=5
VISOR PLATE ANTI-FOG 9100 FX PK=5
LENS COVER OUTER STD 9100 PK=10
COVER LENS OUTER HC 9100 PK=10
LENS COVER OUTER HT 9100 PK=10
LENS COVER INNER 9100XX PK=5
HOLDER BATTERY 9100
SIDEWINDOWS COVER PLATE 9100 FX PK=2
HEAD HARNESS 9100
AIR DUCT ASSEMBLY 9100 FX AIR
ADAPTOR ADFLO BREATHING TUBE 9100 FX AIR
FACE SEAL 9100 FX AIR
AIR DEFLECTOR 9100 FX AIR
HEAD HARNESS PIVOT MECHANISM 9100
Part No
169006
169007
169010
169100
169502
169505
169550
Description
Part No Description
Part No Description
Part No Description
Part No Description
HEAD HARNESS FRONT PART 9100
HEAD HARNESS BACK PART 9100
FRONT COVER KIT 9100 FX
HELMET WELDING 9100 FX AIR EXC LENS
CARRY BAG SPEEDGLAS
To request a quote or place an order for spare parts, please contact TWS on +61 (0)
7
46
5
9 0044 or visit www.tweld.com.au. Please note that higher than normal levels
of pollutants, heat and sparks will require more frequent replacement of components. If you require additional guidance, please check the care and maintenance videos on our
YouTube Channel (
www.youtube.com/user/3MSpeedglas
) or contact your local TWS representative.
Further information and advice
Authorised 3M Wholesaler
Unit 13, 39 Herbert Street • St Leonards NSW 2065 • Australia
T: (02) 9439 0111 • F: (02) 9439 0100
W: www.speedglas.com.au
16 95 02
16 95 05
16 95 50
79 01 01
53 35 05
