Owner’s Manual
400-051-202-01 Rev. B
Page A-7
Figure A-1, Single Operator LOTO Figure A-2, Multiple Operator LOTO
4.
If more than one operator will be working on the machine(s), each operator must
place a padlock and lock tag on the plug lockout. Additional padlocks can be locked
directly through the plug lockout (if the lockout has multiple lock holes) or can be
used in combination with a multi-hole lockout hasp. See Figure A-2.
5.
TEST.
Verify that the machine pair is de-energized by switching the system
controller main power switch to ON. Wait 10 seconds. If the system controller
display remains off (blank) and there are no signs of machine activation (e.g. beeping,
clicking, LEDs on, etc.), the machine pair is de-energized. Otherwise, LOTO has not
been implemented correctly. Repeat Steps 1-4 to ensure LOTO is implemented
correctly. After a successful test, switch the system controller main power switch
back to OFF.
6.
Perform all required maintenance, troubleshooting, cleaning tasks.
7.
Once all work is complete, ensure that all personnel and tools are out of the machine
boundary.
8.
Remove all LOTO devices and re-insert the main power plug into the system
controller.
9.
Switch system controller main power switch to ON.
10.
Press
RESET E-STOP
button on system controller.
11.
Wait for system controller to finish booting up.
12.
Set Odd and Even lane
Chassis Mode
to BOWL.
13.
Press
FULL SET
, then
PLAY
for each lane to reconnect both lanes with facility
scoring system (if installed).
Summary of Contents for Edge String
