PheeNet WMS-308N User Manual Download Page 14

Page: 14 / 154

WMS-308N Network Access Control Gateway

User's Manual

Chapter 3. Base Installations

3.1 Installations

3.1.1 System Requirements

Standard 10/100/1000Base T including five network cables with RJ-45 connectors

All PCs need to install the TCP/IP network protocol

3.1.2 Panel Function Descriptions

Front Panel

Power/Status :

LED

Green

indicates power on,

OFF

indicates power off.

When system restart,

LED

Amber

will flash

three

times after system up.

LED

Amber

indicate the Flash is busy(For example, format database, create or delete accounts...etc)

Console :

The serial RS-232 DB9 cable attaches here.

Reset :

Press and hold the button for more than

seconds until Power/Status

LED

Amber

FLASH

to reset

the system to default configurations. After you release button, the

LED Amber will ON

and system’s

database will be formatted until

LED Green ON

to restart system.

WAN1/WAN2 :

Two WAN ports are available on the system.

LED

Green

indicates

10/100

-Mbps link is

established on the port.

LED

Amber

indicates

1000

-Mbps link is established on the port.

LAN :

Clients devices connect to WMS-308N via LAN ports

Summary of Contents for WMS-308N



























































































































































Search results

Summary of Contents for WMS-308N

Reviews:

Related manuals for WMS-308N

Brands by name

Popular brands

PheeNet WMS-308N, User Manual

Search results

Summary of Contents for WMS-308N

Reviews:

Related manuals for WMS-308N

Brands by name

Popular brands