PheeNet WMS-308N User Manual Download Page 122

Page: 122 / 154

WMS-308N Network Access Control Gateway

User's Manual

122

4.5.7 IP Routing

The IP Routing Settings allows you to configure routing feature in the gateway. The system supports

RIP

(Routing

Information Protocol ) and

OSPF

(Open Shortest Path First) dynamic routing and allows you to manually configure

static network routes. Please click on

Advance -> IP Routing

and follow the below setting.

OSPF Settings

Service :

By default, it's

Disable

. To

Enable

to activated OSPF routing service.

Route ID :

The router ID is typically derived by each router from its interface IP address.

Network :

Specify desired interface

WAN1

WAN2

LAN

VLAN1

VLAN7

for sending and receiving of OSPF

packets.

Area :

Default is

, the range is from

4294967295

Distribute RIP over OSPF :

Allow RIP routes will redistributed into OSPF.

RIP Settings

Service :

By default, it's

Disable

. To

Enable

to activated RIP routing service.

Side(Devices) :

Specify desired interface

WAN1

WAN2

LAN

VLAN1

VLAN7

for sending and receiving of

RIP packets.

Distribute OSPF over RIP :

Allow OSPF routes redistributed into RIP..

Summary of Contents for WMS-308N



























































































































































Search results

Summary of Contents for WMS-308N

Reviews:

Related manuals for WMS-308N

Brands by name

Popular brands

PheeNet WMS-308N, User Manual

Search results

Summary of Contents for WMS-308N

Reviews:

Related manuals for WMS-308N

Brands by name

Popular brands