Chapter 3
Basic Operations
—
Switching on/off the projector
7
0
- ENGLISH
Relationship between brightness and runtime
The projector can be operated
w
ith arbitrary brightness and runti
m
e by setting [LIGHT OUTPUT] to desired
setting.
The relationship bet
w
een the [LIGHT OUTPUT] setting, brightness, and the esti
m
ated runti
m
e is as follo
w
s. Make
the initial setting
(
operation setting
)
depending on the desired brightness of the projected i
m
age and runti
m
e.
The
v
alues of the brightness and the runti
m
e are just an esti
m
ate, and the graph indicating the relationship is just
an exa
m
ple. Also, these do not indicate the
w
arranty period.
[LIGHT OUTPUT] (%)
Brightness (lm)
Estimated runtime
*1
(hours)
100
.
0
30
5
00
2
5 5
00
8
0
.
0
24
000
3
7
000
7
0
.
0
21
000
44
000
6
0
.
0
1
8
000
5
2
000
5
0
.
0
1
5
000
6
1
5
00
*
1
Esti
m
ated runti
m
e is the ti
m
e until the brightness decreases to approxi
m
ately half of the ti
m
e of deli
v
ery
w
hen the projector is used
w
ith the
[PI
C
TURE]
m
enu
→
[DYNAMI
C
C
ONTRAST] set to [
3
] and under en
v
iron
m
ent of
0
.
1
5
m
g
/m
3
dust.
Estimated runtime (hours)
61 500
54 300
47 100
39 900
32 700
25 500
40.0
15 000
50.0
60.0
[LIGHT OUTPUT] (%)
Brightness (lm)
70.0
80.0
90.0
100.0
30 500
Note
f
Under in
fl
uence of characteristics of each light source, conditions of use, installation en
v
iron
m
ent, etc., the runti
m
e
m
ay be shorter than the
esti
m
ation.
f
If the consolidated runti
m
e of the projector exceeds
20
000
hours, replace
m
ent of the co
m
ponents inside the projector
m
ay be required. The
consolidated runti
m
e can be con
fi
r
m
ed in the
[STATUS]
screen. Refer to the [PROJE
C
TOR SETUP]
m
enu
→
[STATUS] for details.
f
After co
m
pleted the initial setting, the
w
ider the co
m
bination of lu
m
inance and runti
m
e beco
m
es by setting the [PROJE
C
TOR SETUP]
m
enu
→
[BRIGHTNESS
C
ONTROL]
→
[BRIGHTNESS
C
ONTROL SETUP]
→
[
C
ONSTANT MODE] to [AUTO] or [P
C
]. Refer to the
[PROJE
C
TOR SETUP]
m
enu
→
[BRIGHTNESS
C
ONTROL] for details.
Initial setting (installation setting)
Set [FRONT
/
REAR] and [FLOOR
/C
EILING] in [PROJE
C
TION METHOD] depending on the installation
m
ode.
Refer to “Installation
m
ode
”
(
x
page
3
6
)
for details.
After co
m
pleted the initial setting, you can change the setting fro
m
the [PROJE
C
TOR SETUP]
m
enu
→
[PROJE
C
TION METHOD].
1) Press
qw
to switch the setting.
执行
SET
CHANGE
Change the projection method (FRONT/REAR,
FLOOR/CEILING) if the screen display is upside down
or inverted.
PROJECTION METHOD
INITIAL SETTING
FRONT/REAR
FLOOR/CEILING
MENU SELECT
FRONT
AUTO
4/7
2) Press the <
执行
> button to proceed to the initial setting.