Chapter 4
Settings
—
[PROJECTOR SETUP] menu
ENGLISH -
1
9
1
5) Press
as
to select a command number, and press the <
执行
> button.
f
You can change the page using
qw
.
6) Press
asqw
to select [TIME], and press the <
执行
> button.
f
The projector is in the adjust
m
ent
m
ode
(
the ti
m
e is blinking
)
.
7) Press
qw
to select “hour” or “minute”, and press
as
or the number (<0> - <9>) buttons to set a
time, and then press the <
执行
> button.
8) Press
asqw
to select [COMMAND].
9) Press the <
执行
> button.
f
The
[COMMAND]
detailed screen is displayed.
10) Press
as
to select a [COMMAND].
f
For [
C
OMMAND]
w
hich requires detailed settings, the ite
m
s of the detailed settings
w
ill s
w
itch each ti
m
e
you press
qw
.
f
When [INPUT] is selected, press the <
执行
> button, and then press
asqw
to select the input to be set.
[COMMAND]
Detailed settings of
[COMMAND]
Description
[POWER ON]
—
S
w
itches on the projector.
[STANDBY]
—
Enters standby.
[SHUTTER]
[OPEN]
Disables the shutter function
(
shutter: opened
)
.
[CLOSE]
Enables the shutter function
(
shutter: closed
)
.
[INPUT]
[HDMI]
S
w
itches the input to HDMI.
[DVI-D]
S
w
itches the input to DVI-D.
[SDI]
S
w
itches the input to SDI.
[DIGITAL LINK]
S
w
itches the input to DIGITAL LINK.
[HDMI1 [SLOT]]
*1
S
w
itches the input to HDMI
1
of the Interface Board.
[HDMI2 [SLOT]]
*1
S
w
itches the input to HDMI
2
of the Interface Board.
[DVI-D1 [SLOT]]
*1
S
w
itches the input to DVI-D
1
of the Interface Board.
[DVI-D2 [SLOT]]
*1
S
w
itches the input to DVI-D
2
of the Interface Board.
[DisplayPort1 [SLOT]]
*1
S
w
itches the input to DisplayPort
1
of the Interface Board.
[DisplayPort2 [SLOT]]
*1
S
w
itches the input to DisplayPort
2
of the Interface Board.
[SDI1 [SLOT]]
*1
S
w
itches the input to SDI
1
of the Interface Board.
[SDI2 [SLOT]]
*1
S
w
itches the input to SDI
2
of the Interface Board.
[SDI3 [SLOT]]
*1
S
w
itches the input to SDI
3
of the Interface Board.
[SDI4 [SLOT]]
*1
S
w
itches the input to SDI
4
of the Interface Board.
[SDI OPT1 [SLOT]]
*1
S
w
itches the input to SDI OPT
1
of the Interface Board.
[SDI OPT2 [SLOT]]
*1
S
w
itches the input to SDI OPT
2
of the Interface Board.
[INPUT1] - [INPUT10]
*2
S
w
itches the input to DIGITAL LINK, and s
w
itches the input of the
DIGITAL LINK output supported de
v
ice to the speci
fi
ed input.
[OPERATING MODE]
*3
[NORMAL]
Prioritizes brightness.
[ECO]
Prioritizes the life of the light source.
[QUIET]
Prioritizes the operation
w
ith lo
w
noise.
[USER1]
C
ontrols the po
w
er
w
ith the setting set to [USER
1
].
[USER2]
C
ontrols the po
w
er
w
ith the setting set to [USER
2
].
[USER3]
C
ontrols the po
w
er
w
ith the setting set to [USER
3
].
*
1
This can be selected
w
hen the optional Interface Board equipped
w
ith corresponding input is installed in <SLOT>.
*
2
When the optional DIGITAL LINK output supported de
v
ice
(
Model No.: ET-YFB
100C)
is connected to the projector, its input na
m
e is
auto
m
atically re
fl
ected fro
m
[INPUT
1
] to [INPUT
10
]. When an ite
m
that does not re
fl
ect the input na
m
e is selected, it
w
ill be disabled.
*
3
If you change the settings
w
hile using the projector, the duration until the lu
m
inance decreases by half
m
ay shorten or the lu
m
inance
m
ay
decrease.
11) Press the <
执行
> button.
f
The co
mm
and is
fi
xed and
n
is displayed at the left of the selected co
mm
and.
f
After the co
mm
and is
fi
xed, press the <
菜单
> button to close the detailed setting screen.
12) Press
asqw
to select [STORE], and press the <
执行
> button.
