Panasonic MSDA043A1A Operating Manual Download Page 62 | Manualshive

Page: 62 / 183

background image

−

61

−

How to Adjust the Gain at Position Control Mode

① Start the motor (machine).
② Set Pr10 (1st Position Loop Gain) to 50.
③ Increase the value of Pr11 (1st Velocity Loop Gain) gradually until the motor

(machine) does not generate abnormal sound or vibration.

④ Increase the value of Pr10 (1st Position Loop Gain) gradually until the motor

(machine) does not generate abnormal sound or vibration.

⑤Decrease the value of Pr12 (1st Velocity Loop Integration Time Constant) accord

ing to the In-position time.

・With a larger value, positional errors may not be converged.

⑥ If you want to improve the response further, adjust Pr15 (Velocity Feed Forward)

within the extent that the

motor (machine) does not generate abnormal sound or

vibration.

・With a larger value, overshoot and/or chattering of in-position signals may occur,

which results in a

longer in-position time. Note that this may be improved by ad-

justing the value of Pr16 (Feed Forward Filter).

How to Adjust the Gains for Velocity Control

1.If the controller does not have a position loop gain

Adjust Pr11 (1st Velocity Loop Gain) and Pr12 (1st Velocity Loop Integration Time
Constant). Note that Pr15 (Velocity Feed Forward) is not effective.

① Increase the value of Pr11 (1st Velocity Loop Gain) gradually until the motor

(machine) does not generate abnormal sound or vibration.

②Decrease the value of Pr12 (1st Velocity Loop Integration Time Constant) gradu-

ally until the overshoot/undershoot is reduced to an acceptable level.

2.

If the controller has a position loop gain

①Set Pr58 (Acceleration Time Set-Up), Pr59 (Deceleration Time Set-Up) and Pr5A

(S-Curve Accel/Decel Time Set-Up) to 0.

② Increase the value of Pr11 (1st Velocity Loop Gain) gradually until the motor

(machine) does not generate abnormal sound or vibration.

③Decrease the value of Pr12 (1st Velocity Loop Integration Time Constant) gradu-

ally until the overshoot/undershoot is reduced to an acceptable level.

④ Adjust the position loop gain on the controller.

<Notes>

Position loop gain changes when you change the value of Pr50 (Velocity Command

Input Gain).

Relationship between command voltage and velocity

6V at 3000r/min
6V at 1500r/min
6V at 4500r/min

Pr50 value

Default = 500

250
750

Position loop gain set in the controller

Assuming this is 1

1/2

1.5 times

Preparations and Adjustment

Examples

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
60
61
62
63
64
...
»

Summary of Contents for MSDA043A1A
























































































































































































Reviews:

No comments

Related manuals for MSDA043A1A

Brand: Omron Pages: 9

Brand: Lenze Pages: 2

Brand: Baldor Pages: 42

Brand: Label Pages: 56

Brand: Leadshine Pages: 13

RolloTron Pro Star Series

Brand: RADEMACHER Pages: 72

Rolltron PRO comfort

Brand: RADEMACHER Pages: 76

Brand: TPM Pages: 28

Brand: Simu Pages: 24

Brand: ZIEHL-ABEGG Pages: 123

Sonesse Ultra 50 RTS

Brand: SOMFY Pages: 52

Brand: Panasonic Pages: 17

L1000A CIMR-LC F Series

Brand: YASKAWA Pages: 106

Brand: Baldor Pages: 20

ZPSA-600-EH1-FR Series

Brand: YASKAWA Pages: 42

Brand: Danfoss Pages: 118

Brand: Danfoss Pages: 226

MOVIMOT MMxD Series

Brand: SEW-Eurodrive Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands