Panasonic LightPix AE20 User Manual Download Page 99

Page: 99 / 151

4.6.6 Setting Up Judgement Criteria in JUDGEMENT CRITERIA and

MEASUREMENT OBJECT MIN. SETTING modes

Based on the base measurement saved by teaching, the allowable limits for OK judgement specified each in
X and Y direction in mm.

Operation in JUDGEMENT CRITERIA SETTING mode

In INSPECTION (or RUN) mode

In JUDGEMENT CRITERIA SETTING mode (“SET” is displayed.)

Referring the value saved during teaching

•

RMinX: Min. in the X direction

•

RMaxX: Max. in the X direction

•

RMinY: Min. in the Y direction

•

RMaxY: Max. in the Y direction

Allowable range to be set

•

PMinX: Min. in the X direction

•

PMaxX: Max. in the X direction

•

PMinY: Min. in the Y direction

•

PMaxY: Max. in the Y direction

•

The <8> button: Increases the value

•

The <7> button: Decreases the value

MinX: Min. for Measurement Object - in the X
direction

•

The <8> button: Increases the value

•

The <7> button: Decreases the value

MinY: Min. for Measurement Object - in the Y
direction

•

The <8> button: Increases the value

•

The <7> button: Decreases the value

Summary of Contents for LightPix AE20
























































































































































Search results

Summary of Contents for LightPix AE20

Reviews:

Related manuals for LightPix AE20

Brands by name

Popular brands

Panasonic LightPix AE20, User Manual

Search results

Summary of Contents for LightPix AE20

Reviews:

Related manuals for LightPix AE20

Brands by name

Popular brands