Panasonic LightPix AE20 User Manual Download Page 30

Page: 30 / 151

3.4.3 Output

Signal

Circuit

Output part: PhotoMos relay
The output load should be within the specified range. See the figure shown below.

Notes on Parallel Output

•

Leakage current at the time of output signal OFF is less than 100 µA.

•

The LightPixAE20 has a low load capacity so that you can connect the LightPixAE20 to a PLC, etc. Do

not connect directly with a device having a high load capacity such as a valve without passing it through
our Power-Photo relay.

•

The output circuit contains no built-in fuse. If it is necessary to prevent from burning out the output

circuit in the event of output load short circuit, mount a fuse externally. However, it may not be able to
protect internal elements in the event of short circuit.

Summary of Contents for LightPix AE20
























































































































































Search results

Summary of Contents for LightPix AE20

Reviews:

Related manuals for LightPix AE20

Brands by name

Popular brands

Panasonic LightPix AE20, User Manual

Search results

Summary of Contents for LightPix AE20

Reviews:

Related manuals for LightPix AE20

Brands by name

Popular brands