Panasonic LightPix AE20 User Manual Download Page 39 | Manualshive

Page: 39 / 151

Panasonic LightPix AE20 User Manual Download Page 39

4.2 Color Area and Color Judgement

4.2.1 Overview of Color Area

The Color Area application is used for measuring the registered color area. It judges whether or not the
measured color area values are within the set area range, and if the color area values are within the range
(OK judgement), the OUT1 signal is turned on, if they are out of the range (NG judgement), the OUT1
signal is turned off. You can register one product type for each color and totally seven colors for seven
product types, but inspection is performed for each product type. If you want to inspect the object in the
color different from the color that is saved as the current product type, change to the desired product type at
the LightPix side first and continue the inspection.

Example:
Registered data

Area range

Product
type No.

Registered
color

Min.

Max.

1 Red

200

300

2 Blue 200

300

Operations of AE20

32

«
...
37
38
39
40
41
...
»

Summary of Contents for LightPix AE20
























































































































































Reviews:

No comments