Panasonic LightPix AE20 User Manual Download Page 77 | Manualshive

Page: 77 / 151

background image

4.5 Peak Detection

4.5.1 Overview of Peak Detection

In a binarized image, the unit detects a point in the inspection area. If the base point saved in TEACHING
mode is detected, and the distance between the left upper of the point in the inspection area where the point
is detected and the detected point is within the base po/- allowable range, the image is judged as OK,
and OUT1 is turned ON.

Detectable and undetectable peaks

The unit detects two points in the X and Y directions by computing the intersected point. The X- and Y-
directional distance between the left upper part of the point in the inspection area and the detected point is
displayed as a the position of the detected point in mm.

Example detectable images

These are examples of black objects against a white background, but the unit can also detect a white
object against a black background.

Undetectable image

70

«
...
75
76
77
78
79
...
»

Summary of Contents for LightPix AE20
























































































































































Reviews:

No comments

Related manuals for LightPix AE20

Brand: Uhlenbrock Elektronik Pages: 12

Brand: Icom Pages: 9

Brand: Icom Pages: 16

Brand: TILLQUIST Pages: 15

Brand: Precision Electronics Pages: 3

Brand: Trio Pages: 19

Brand: sebaKMT Pages: 46

Brand: Zaxcom Pages: 35

Brand: M-system Pages: 3

Brand: M-system Pages: 7

ALAN 100 PLUS B

Brand: Midland Pages: 40

interface modul IMC-AIA-11Ex-i/24VDC

Brand: turck Pages: 4

Brand: SIIG Pages: 11

5819WHS - Ademco Wireless Shock Processor

Brand: ADEMCO Pages: 2

Brand: Renkforce Pages: 8

AudioLink II IRT-951C

Brand: ELT Group Pages: 7

Brand: Safe Fleet Pages: 34

Brand: Kirisun Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands