Panasonic DA-DU26C Operating Instructions Manual Download Page 150

Page: 150 / 166

Maintenance

Replacing the Toner Cartridges

138

b. Turn

the

Rotary Knob

in the direction of the arrow until it stops.

Repeat the steps until the desired cartridge is visible in the opening.

With the desired cartridge visible in the opening, turn the cartridge in the
direction of the arrow until the

Dot

is aligned with the

Unlock

symbol.

Pull the Toner Cartridge out of the Printer.

WARNING

DO NOT

attempt to use old cartridges, as they could cause print quality

problems.

NEVER

dispose of old toner cartridges in an open flame. Toner is

flammable and could explode, causing burns and other injuries.

Summary of Contents for DA-DU26C







































































































































































Search results

Summary of Contents for DA-DU26C

Reviews:

Related manuals for DA-DU26C

Brands by name

Popular brands

Panasonic DA-DU26C, Operating Instructions Manual

Search results

Summary of Contents for DA-DU26C

Reviews:

Related manuals for DA-DU26C

Brands by name

Popular brands