No.
Name
Description
Range
Def.
Control
Mode
Addr.
Hex
Pg.
V/f O
LV
P
M
r1-39
FBDs Connection Parameter
20 (upper)
Parameter 20 for connecting FBDs (upper).
0 to
FFFFH
0
– A A
1866
—
r1-40
FBDs Connection Parameter
20 (lower)
Parameter 20 for connecting FBDs (lower).
0 to
FFFFH
0
– A A
1867
—
u
T: Motor Tuning
Enter data into the following parameters to tune the motor and drive for optimal performance
No.
Name
Description
Range
Def.
Control
Mode
Addr.
Hex
Pg.
V/f O
LV
P
M
T1-00
Motor Selection 1/2
Selects which set of motor parameters are used and set during
Auto-Tuning. If Motor 2 selection (H1-
= 16) is not selected,
this parameter will not be displayed.
1: 1st Motor - E1 to E2
2: 2nd Motor - E3 to E4 (this selection is not displayed if motor 2
has not been selected)
2: 2nd Motor - E3 to E4
1, 2
1
A A −
700
90
T1-01
Auto-Tuning Mode
Selection
Selects the Auto-Tuning mode.
0: Rotational Auto-Tuning
2: Stationary Auto-Tuning for Line-to-Line Resistance
3: Rotational Auto-Tuning for V/f Control (necessary for Energy
Savings and Speed Estimation type Speed Search)
0, 2, 3
<54>
2 or 3 in
V/f
0 or 2 in
OLV
2 in
Motor 2
A A −
701
90
T1-02
Motor Rated Power
Sets the motor rated power in kilowatts (kW).
Note:
If motor power is given in horsepower, power in kW can be
calculated using the following formula: kW = HP x 0.746.
0.00 to
650.00
<12>
A A −
702
90
T1-03
<24>
Motor Rated
Voltage
Sets the motor rated voltage in volts (V).
0.0 to
255.5
200.0 V A A −
703
90
T1-04
Motor Rated Current
Sets the motor rated current in amperes (A).
10 to 200%
of drive
rated
current
<12>
A A −
704
91
T1-05
Motor Base
Frequency
Sets the base frequency of the motor in Hertz (Hz).
0.0 to
400.0
60.0 Hz A A −
705
91
T1-06
Number of Motor
Poles
Sets the number of motor poles.
2 to 48
4
A A −
706
91
T1-07
Motor Base Speed
Sets the base speed of the motor in revolutions per minute r/min
(RPM).
0 to 24000 1750 r/
min
A A −
707
91
T1-11
Motor Iron Loss
Provides the iron loss for determining the Energy Saving
coefficient.
The value set to E2-10 (motor iron loss) when the power is cycled.
If T1-02 is changed, an initial value valid for the selected capacity
will be shown.
0 to 65535
14 W
A − −
70B
91
These values differ depending on the
motor code value and motor
parameter settings.
<12> Default setting value is dependent on parameter o2-04, Drive Model Selection.
<24> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.
<54> The available tuning methods depend on control mode. Select values 2 or 3 in V/f Control, 0 or 2 in OLV control, and 2 for Motor 2 control.
u
U: Monitors
Monitor parameters allow the user to view drive status, fault information, and other information about drive operation.
No.
Name
Description
Analog Output
Level
Unit
Control
Mode
Addr.
Hex
V/f O
LV
P
M
U1: Operation Status Monitors
Use U1 monitors to display the operation status of the drive.
U1-01
Frequency Reference
Monitors the frequency
10 V: Max
frequency
0.01
Hz
A A A
40
U1-02
Output Frequency
Displays the output frequency. Display units are
determined by o1-03.
10 V: Max
frequency
0.01
Hz
<27>
A A A
41
U1-03
Output Current
Displays the output current.
10 V: Drive rated
current
0.01A A A A
42
B.2 Parameter Table
332
SIEP C710606 20 OYMC AC Drive - V1000 User Manual
7/16/2008-13:23
