Motor 2 Selection ...................................................... 315, 318
Motor 2 Torque Compensation Gain...................................... 310
Motor Acceleration Time for Inertia Calculations ...................... 323
Motor Armature Resistance (for PM motor) ............................. 311
Motor Base Frequency .................................................. 89, 332
Motor Base Speed ........................................................... 332
Motor Data Error....................................................... 229, 250
Motor d-Axis Current at Previous Fault .................................. 334
Motor d Axis Inductance (for PM motor) ................................ 311
Motor Direction at Power Up when Using Operator.................... 329
Motor Does Not Operate When an External Run Command is Input
.................................................................................. 259
Motor Does Not Operate When the RUN Button on the Digital Operator
is Pressed...................................................................... 259
Motor Does Not Rotate ..................................................... 253
Motor Excitation Current (ld) .............................................. 337
Motor Hunting and Oscillation Control Parameters .................... 225
Motor Hunting Occurs at Low Speeds.................................... 255
Motor Hunting Occurs When Operating With a Light Load........... 256
Motor Induction Voltage Constant 1 (for PM motor)................... 311
Motor Induction Voltage Parameter 2 (for PM motor) ................. 311
Motor Iron-Core Saturation Coefficient .................................. 250
Motor Iron-Core Saturation Coefficient 1 ................................ 309
Motor Iron-Core Saturation Coefficient 2 ................................ 309
Motor Iron-Core Saturation Coefficient 3 ................................ 309
Motor Iron Core Saturation Coefficient Error ........................... 229
Motor Iron Loss .............................................................. 332
Motor Iron Loss for Torque Compensation .............................. 309
Motor is Too Hot ............................................................ 254
Motor Leakage Inductance ................................................. 309
Motor Line-to-Line Resistance ............................................ 309
Motor Mechanical Loss ..................................................... 309
Motor No-Load Current..................................................... 309
Motor Operates at a Higher Speed than the Speed Command......... 259
Motor Overheat ........................................................ 228, 244
Motor Overheat 1 (PTC input) ............................................. 228
Motor Overheat 2 (PTC input) ............................................. 228
Motor Overheat Alarm (PTC Input)....................................... 235
Motor Overheat Alarm Operation Selection (PTC input) .............. 321
Motor Overheat Fault (PTC Input) ........................................ 235
Motor Overheat Fault Operation Selection (PTC input)................ 321
Motor Overload ........................................................ 228, 235
Motor Overload Estimate (oL1) ........................................... 336
Motor Overload Protection Selection ............................... 321, 390
Motor Overload Protection Time .................................... 321, 390
Motor Poles..................................................................... 89
Motor Poles (for PM motor)................................................ 311
Motor Produces Insufficient Torque ...................................... 258
Motor Protection Function.................................................. 236
Motor q-Axis Current at Previous Fault .................................. 334
Motor Rated Capacity (for PM motor).................................... 311
Motor Rated Current ........................................ 89, 309, 332, 390
Motor Rated Current (for PM motor) ..................................... 311
Motor Rated Output ......................................................... 309
Motor Rated Power .......................................................... 332
Motor Rated Slip............................................................. 309
Motor Rated Voltage .................................................... 89, 332
Motor Rotates After the Drive Output is Shut Off ...................... 258
Motor Rotates Faster Than the Frequency Reference................... 256
Motor Rotates in One Direction Only............................... 254, 259
Motor Secondary Current (Iq) ............................................. 337
Motor Selection 1/2.......................................................... 332
Motor Speed .................................................................. 333
Motor Speed at Previous Fault ............................................. 334
Motor Speed Error ........................................................... 229
Motor Speed Fault ........................................................... 251
Motor Stalls During Acceleration or With Large Loads ............... 255
Motor Stops During Acceleration or When a Load is Connected..... 259
Motor Switch during Run................................................... 245
Motor Temperature (PTC input)........................................... 319
Motor Temperature Input Filter Time (PTC input) ..................... 321
Motor Wiring................................................................... 48
Multi-Function Analog 1 (Terminal AM Monitor Selection).......... 319
Multi-Function Analog Input Selection Error...................... 229, 248
Multi-Function Digital Inputs................................................ 51
Multi-Function Digital Input Terminal S1 Function Selection ........ 315
Multi-Function Digital Input Terminal S2 Function Selection ........ 315
Multi-Function Digital Input Terminal S3 Function Selection ........ 315
Multi-Function Digital Input Terminal S4 Function Selection ........ 315
Multi-Function Digital Input Terminal S5 Function Selection ........ 315
Multi-Function Digital Input Terminal S6 Function Selection ........ 315
Multi-Function Digital Output ............................................... 51
Multi-Function Input Selection Error ..................................... 247
Multi-Function Input Setting Error........................................ 229
Multi-Function Photocoupler Output ....................................... 51
Multiple Drive Wiring ........................................................ 48
Multi-Step Speed Reference................................................ 315
Multi-Step Speed Reference 4 ............................................. 316
N
NEMA Type 1.................................................................. 35
Noise From the Drive or Output Lines When the Drive is Powered On
.................................................................................. 257
No-Load Current Error................................................ 229, 251
No-Load Operation ............................................................ 92
Normal Duty Ratings........................................................ 131
Number of Auto Restart Attempts......................................... 323
Number of Motor Poles ............................................... 309, 332
Number of Run Commands ................................................ 335
Number of Speed Search Restarts ......................................... 301
O
Offset Frequency............................................................. 337
Offset Frequency 1 .......................................................... 308
Offset Frequency 1 Addition ............................................... 316
Offset Frequency 2 .......................................................... 308
Offset Frequency 2 Addition ............................................... 316
Offset Frequency 3 .......................................................... 308
Offset Frequency 3 Addition ............................................... 316
OPE Fault Parameter ........................................................ 333
Open-Chassis IP20 ............................................................ 33
Open Loop Vector ........................................................... 251
Open Loop Vector Control ....... 225, 230, 238, 254, 255, 256, 257, 258
Open Loop Vector Control Mode Tuning ................................ 224
Open Loop Vector Control Mode Tuning Parameters .................. 224
Operating with the Load Connected......................................... 93
Operation Errors ....................................................... 227, 229
Operation Selection at Deviation (for Simple PG V/f Control) ....... 312
Operation Selection at Overspeed (OS) (for Simple PG V/f).......... 312
Operation Selection at PG Open Circuit (PGO) ......................... 312
Operation Selection when Digital Operator is Disconnected .......... 329
Operator Connection Fault ................................................. 228
Operator Programming Errors ............................................. 247
Option/Drive Selection...................................................... 315
Option Card Communications Error ...................................... 228
Option Card External Fault..................................... 228, 232, 242
Index
SIEP C710606 20 OYMC AC Drive - V1000 User Manual
403
7/16/2008-13:23