8
Installing and Uninstalling the Software
Section 2-1
2-1
Installing and Uninstalling the Software
2-1-1
Software That Must Be Installed
The following software must be installed on the same computer to use the CX-
Motion-NCF.
1,2,3...
1.
CX-Motion-NCF
2.
CX-Server (the communications driver)
Installing of CX-Motion-
NCF
Refer to the
CX-One Ver. 3.0 Setup Manual
(Cat. No. W463) (supplied with
the CX-One FA Integrated Tool Package) for information on how to install or
uninstall the CX-Motion-NCF from the CX-One FA Integrated Tool Package.
2-2
Connecting to PLC
To transfer the project data that was created using CX-Motion-NCF to the
Position Control Unit. The personal computer and PLC (CPU Unit) must be
physically connected with a cable and also connected online.
2-2-1
Connecting to CS/CJ-series PLCs
Connection Format
Using either the Host Link (SYSMAC WAY) or Toolbus, connect the personal
computer to the peripheral port or RS-232C port on the PLC.
Note
The cable model CS1W-CN118 is used as a relay cable to connect the per-
sonal computer to the CPU Unit's peripheral port using the RS-232C cable
(model XW2Z-
@@@@
-
@@
) as shown below.
Cat. No.
Model
Manual name
Contents
W463
CXONE-AL
@@
C-V3/
CXONE-AL
@@
D-V3
CX-One Ver. 3.0
Setup Manual
An overview of the CX-One
FA Integrated Tool Package
and the CX-One installation
procedure
Personal
computer
Connecting to Peripheral Port
Connecting to RS-232C Port
IBM PC/AT
or compati-
ble
NEC
PC-9801
BX
10-pin
CS1W-CN118 (0.1 m) (See note.)
CS1W-CN226 (2.0 m)
CS1W-CN626 (6.0 m)
CS1W-CN118
CS1W-CN226
CS1W-CN626
9-pin
male
9-pin
female
Peripheral port
(10-pin female)
(See note.)
9-pin
female
NEC
PC-9801
BX
XW2Z-200S-CV / 200S-V (2.0 m)
XW2Z-500S-CV / 500S-V (5.0 m)
XW2Z-200S-CV / -200S-V
XW2Z-500S-CV / -500S-V
9-pin
male
9-pin
female
9-pin
male
9-pin
female
9-pin
male
RS-232C port
(9-pin female)
NEC
PC-9801
BX
CS1W-CN118
RS-232C Cable
Peripheral Port
Summary of Contents for CX-MOTION-NCF - V1.8
