114
Revision History
03
November 2005 Writing style unified for certain aspects of the manual.
The following changes were made to update to version 1.3 and correct information in
the manual.
Page xiv:
Version upgrade information and unit version information added.
Page xvi:
Last warning and first caution modified and last warning changed to a
caution in
Safety Precautions.
Page xvii:
Third application precaution modified.
Pages ix, 42, 44, 45, and 104:
CS1W-NCF71 added.
Page 2:
Minor section added.
Pages 2, 22, 25, 26, 27, 29, 36, 37, 39, 40, 71, 72, and 73:
Figure replaced.
Page 5:
Introduction to
1-2 System Configuration
changed.
Page 6:
Description of
Device information
changed and
Error information
row
removed from table.
Pages 6, 30, 33, and 93:
Absolute Encoder Setup operation added.
Page 32:
“CX-One/” added.
Page 33:
Description of
Displaying device information
changed.
Page 36:
Section
4-1 Creating a New Project
replaced.
Page 45:
Next to last row of table corrected.
Page 58:
NSJ Controller added.
Page 105:
Row added to table under
Cannot connect to the NC Unit...
and rows
added to end of table.
04
July 2006
Pages ix, 3, and 10:
Cat. No. and models changed.
Pages xiv and 2:
Information on CP-series PLCs added.
Page 3:
Table replaced.
Page 19:
Heading added.
Page 20:
Section added.
Page 89:
Screen shot replaced.
05
November 2006 Changes were made to upgrade to software version 1.4
Page xiv:
Version upgrade information added for version 1.4.
Page xvi:
CS1W-NCF71 added.
Page xvi:
Information added on unit version 2.0.
Pages xvi and108 to 111:
Information added on SMARTSTEP Junior Servo Driv-
ers.
Page 13:
Step added to procedure.
Page 40:
Information added to note.
Page 47:
First two rows of table combined.
Pages 46, 48, 55, 111, xvi:
Note added.
Page 48:
Screen capture replaced and steps added to procedure.
Page 57:
Printing sample replaced.
Pages 63, 66, 68, 70, 72, 75, 80, 83, and 94:
Screen capture replaced.
Page 86:
Screen capture replaced.
Page 90:
Additions made to status monitor table.
Page 108:
Section heading changed.
06
June 2007
Pages ix and 2:
Operating system added.
Page xiv
: Improvements updated.
Page 3:
Information on applicable computers replaced and deleted.
Page 4
: Section on checking the package deleted.
Pages 10 and 11
: Information on software replaced and sections on preparing
installation deleted.
Pages 12 to 19:
Sections on installing and uninstalling CX-Motion-NCF and CX-
Server deleted.
Page 117
: Information on Windows 2000 SP2 deleted.
Revision code
Date
Revised content
Summary of Contents for CX-MOTION-NCF - V1.8
