102
Error Codes
Section 11-2
---
---
---
84
4054
Transfer cycle error Command cannot be received in
transfer cycle of MECHATROLINK-II
communications.
---
---
---
87
4057
Immediate stop
input error
Immediate input has turned to open.
---
---
---
90
405A
Transfer cycle set-
ting error
There is a problem in the transfer
cycle setting.
---
---
---
93
405D
Parameter setting
error
The electronic gear ratio is less than
1/100 or it is larger than 100: Parame-
ter setting has exceeded the allow-
able range.
---
---
---
95
405F
Motor does not
match
The Servomotor are Servo Drive
combination is incorrect.
A.71
A.71
@
A.71
---
4071
Overload
Operating with output torque exceed-
ing 245% of the rated torque.
A.72
A.72
@
A.72
---
4072
Overload
Operation continuing with output
torque at 120% to 245% of the rated
torque.
A.73
A.73
@
---
---
4073
Dynamic brake
overload
The rotary energy has exceeded the
dynamic brake resistor capacity dur-
ing dynamic brake operation.
---
---
A.73
---
The Servomotor did not stop 3 sec-
onds or more after the Servo Drive
was turned OFF.
A.74
A.74
@
---
---
4074
Inrush resistance
overload
The inrush current when power was
turned ON exceeded the inrush resis-
tor capacity.
A.7A
A.7A
@
---
---
407A
Overheat
Overheating in the radiation shield
was detected.
---
---
A.7A
---
Board overheated
The Servo Drive has overheated or
the built-in cooling fan has stopped.
A.81
A.81
@
---
---
4081
Backup error
(Absolute encoders
only)
The encoder's backup power supply
has fallen.
A.82
A.82
@
---
---
4082
Checksum error
(Absolute encoders
only)
An encoder memory checksum error
has occurred.
A.83
A.83
@
---
---
4083
Battery error
(Absolute encoders
only)
The encoder's battery voltage has
fallen (to 2.7 V or lower).
A.84
A.84
@
---
---
4084
Absolute error
(Absolute encoders
only)
An internal encoder data error has
occurred.
A.85
A.85
@
---
---
4085
Overspeed error
(Absolute encoders
only)
The Servomotor is rotating at 200 r/
min. or more when the encoder
power supply is turned ON.
A.86
A.86
@
---
---
4086
Encoder overheat-
ing
(Absolute encoders
only)
Overheating in the encoder was
detected.
A.b1
---
---
---
40B1
Speed command
input reading error
The A/D completion signal from the
A/D converter is not being output
within the fixed interval.
Servo Drive display
Position
Control
Unit error
code
Error detection
function
Detected error or cause of error
W
Series
W-series
(Built-in
Communi-
cations
Type)
SMART-
STEP Jun-
ior (Built-in
communi-
cations
Type)
G-Series
(Built-in
communi-
cations
Type)
Summary of Contents for CX-MOTION-NCF - V1.8
