Nivus osm-f, Operation Instruction Manual

Page: 97 / 103

Instruction Manual
OCM F
OCM F - Rev. 04 as of 18.02.2014 Page 97
15 Emergency
In case of emergency
− press the emergency-off button of the main system or
− set the slide switch (see Fig. 7-12) on the unit to OFF.
16 Dismantling/Disposal
The device shall be disposed according to the local regulations for electronic
products.
17 Table of Pictures
Fig. 3-1 Transmitter nameplate ........................................................................................................................ 8
Fig. 4-1 Overview ............................................................................................................................................. 9
Fig. 5-1 Construction of combi sensor Type “KDA“ with additional pressure measurement cell ...................13
Fig. 5-2 Construction pipe sensor, type KDA ................................................................................................. 14
Fig. 5-3 Type key for OCM F measurement transmitter ................................................................................. 16
Fig. 7-1 Wall mount enclosure ........................................................................................................................ 19
Fig. 7-2 Connection Enclosure ....................................................................................................................... 23
Fig. 7-3 Clamp wiring OCM F ......................................................................................................................... 24
Fig. 7-4 Connection of 1 wedge or pipe sensor (no Ex), Type K0 or R0 .......................................................25
Fig. 7-5 Connection of 1 KDA combi sensor (no Ex) with integrated pressure measurement cell, Type KP 25
Fig. 7-6 Connection of 1 KDA wedge or pipe sensor (Ex), Type K0 or R0 .................................................... 26
Fig. 7-7 Connection of 1 KDA combi sensor (Ex) with integrated pressure measurement cell, Type KP ..... 26
Fig. 7-8 Connecting an ext. 2-wire sensor (no Ex) for flow level measurement............................................. 26
Fig. 7-9 Connecting a NIVUS i-Serial sensor for level measurement in Ex-Zone 1 ...................................... 27
Fig. 7-10 Connecting an ext. 2-wire sensor (Ex) for flow level measurement..................................................27
Fig. 7-11 Connecting an external flow level measurement via NivuMaster ..................................................... 27
Fig. 7-12 Slide switch position in terminal clamp housing ................................................................................ 28
Fig. 7-13 AC model power supply .................................................................................................................... 28
Fig. 7-14 DC model power supply .................................................................................................................... 29
Fig. 7-15 Connecting the overvoltage protection for power supply and analog inputs and outputs ................ 30
Fig. 7-16 Overvoltage protection compact Doppler active sensor ...................................................................31
Fig. 7-17 Overvoltage protection compact Doppler active sensor (Ex) ............................................................ 31
Fig. 7-18 Setup of a controlled system such as a discharge control ................................................................ 33
Fig. 7-19 Wiring diagram for controller operation ............................................................................................. 34
Fig. 8-1 Keypad .............................................................................................................................................. 37
Fig. 8-2 Main screen ....................................................................................................................................... 37
Fig. 8-3 Auxiliary screen................................................................................................................................. 38
Fig. 9-1 Screen on end of parameter setting .................................................................................................. 40
Fig. 9-2 Language selection ........................................................................................................................... 41
Fig. 9-3 Operation mode selection ................................................................................................................. 41
Fig. 9-4 Day values ......................................................................................................................................... 42
Fig. 9-5 Time of day totalising ........................................................................................................................ 42
Fig. 9-6 Error message...................................................................................................................................43
Fig. 9-7 Extra-submenus ................................................................................................................................ 44
Fig. 9-8 System information............................................................................................................................ 44
Fig. 9-9 Additional system information ........................................................................................................... 44
Fig. 9-10 Selecting the unit system .................................................................................................................. 45
Fig. 9-11 Selecting the units ............................................................................................................................. 45
Fig. 9-12 Selecting the display format ..............................................................................................................45
Fig. 9-13 system time - submenus ................................................................................................................... 46
Fig. 9-14 complete system time ....................................................................................................................... 46
Fig. 9-15 Totalizer modification ........................................................................................................................ 46