Digitax HD M753 Control User Guide
41
Issue Number: 3
6 Basic parameters
Menu 0 is used to bring together various commonly used parameters for basic easy set up of the drive. All the parameters in Menu 0 appear in other
menus in the drive (denoted by {…}). Menus 22 can be used to configure the parameters in Menu 0.
6.1
Parameter ranges and variable minimum / maximums
Some parameters in the drive have a variable range with a variable minimum and a variable maximum value which is dependent on one of the
following:
•
The settings of other parameters
•
The drive rating
•
The drive mode
•
Combination of any of the above
For more information, refer to section 12.1
Parameter ranges and Variable minimum/maximums
6.2
Menu 0: Basic parameters
Parameter
Range
Default
Type
OL
RFC-A
RFC-S
OL
RFC-A
RFC-S
00.001
Minimum Reference Clamp
{01.007}
VM_NEGATIVE_REF_CLAMP1 Hz / rpm
0.0 Hz
0.0 rpm
RW Num
US
00.002
Maximum Reference Clamp
{01.006}
VM_POSITIVE_REF_CLAMP1 Hz / rpm
50 Hz default:
50.0 Hz
60 Hz default:
60.0 Hz
50 Hz default:
1500.0 rpm
60 Hz default:
1800.0 rpm
3000.0 rpm
RW Num
US
00.003
Acceleration Rate 1
{02.011}
0.0 to
VM_ACCEL_RATE
s/100 Hz
0.000
to
VM_ACCEL_RATE
s/1000 rpm
5.0 s/100 Hz
2.000
s/1000 rpm
0.200
s/1000 rpm
RW Num
US
00.004
Deceleration Rate 1
{02.021}
0.0 to
VM_ACCEL_RATE
s/100 Hz
0.000
to
VM_ACCEL_RATE
s/1000 rpm
10.0 s/100 Hz
2.000
s/1000 rpm
0.200
s/1000 rpm
RW Num
US
00.005
Reference Selector
{01.014}
A1 A2 (0), A1 Preset (1), A2 Preset (2), Preset (3),
Keypad (4), Precision (5), Keypad Ref (6)
A1 Preset (1)
RW
Txt
US
00.006
Symmetrical Current Limit
{04.007}
0.0 to VM_MOTOR1_CURRENT_LIMIT %
165.0 %
250 %
RW Num
RA
US
00.007
Open-loop Control Mode
{05.014}
Ur S (0), Ur (1),
Fixed (2),
Ur Auto (3), Ur I (4),
Square (5)
Ur I (4)
RW
Txt
US
Speed Controller Proportional Gain
Kp1
{03.010}
0.0000 to 200.000 s/rad
0.0300 s/rad
0.0100 s/rad RW Num
US
00.008
Low Frequency Voltage Boost
{05.015}
0.0 to 25.0 %
1 %
RW Num
US
Speed Controller Integral Gain Ki1
{03.011}
0.00 to 655.35 s
2
/rad
0.10 s
2
/rad
1.00 s
2
/rad
RW Num
US
00.009
Dynamic V to F Select
{05.013}
Off (0) or On (1)
Off (0)
RW
Bit
US
Speed Controller Differential
Feedback Gain Kd 1
{03.012}
0.00000 to 0.65535 1/rad
0.00000 1/rad
RW Num
US
00.010
Motor Rpm
{05.004}
±180000 rpm
RO
Bit
US
Speed Feedback
{03.002}
VM_SPEED rpm
RO Num ND NC PT
FI
00.011
Output Frequency
{05.001}
VM_SPEED_
FREQ_REF Hz
± 2000.0 Hz
RO Num ND NC PT
FI
P1 Position
{03.029}
0 to 65535
RO Num ND NC PT
FI
00.012
Current Magnitude
{04.001}
0.000 to VM_DRIVE_CURRENT_UNIPOLAR A
RO
Bit
ND NC PT
FI
00.013
Torque Producing Current
{04.002}
VM_DRIVE_CURRENT A
RO
Bit
ND NC PT
FI
00.014
Torque Mode Selector
{04.011}
0 or 1
0 to 5
0
RW Num
US
00.015
Ramp Mode
{02.004}
Fast (0),
Standard (1),
Std boost (2)
Fast (0), Standard (1)
Standard (1)
Fast (0)
RW
Txt
US
00.016
Ramp Enable
{02.002}
Off (0) or On (1)
On (1)
RW
Bit
US
00.017
Current Reference Filter 1 Time
Constant
{04.012}
0.0 to 25.0 ms
0.0 ms
RW Num
US
00.018
P1 Thermistor Fault Detection
{03.123}
None (0), Temperature (1), Temp or Short (2)
None (0)
Temperature
(1)
RW
Txt
US
00.022
Bipolar Reference Enable
{01.010}
Off (0) or On (1)
Off (0)
On (1)
RW
Bit
US
00.023
Jog Reference
{01.005}
0.0 to 400.0 Hz
0.0 to 4000.0 rpm
0.0
RW Num
US
00.024
Preset Reference 1
{01.021}
VM_SPEED_FREQ_REF 0.0
RW Num
US
00.025
Preset Reference 2
{01.022}
VM_SPEED_FREQ_REF 0.0
RW Num
US
00.026
Preset Reference 3
{01.023}
VM_SPEED_
FREQ_REF Hz
0.0
RW Num
US
Overspeed Threshold
{03.008}
0 to 40000 rpm
0.0
RW Num
US
00.027
Preset Reference 4
{01.024}
VM_SPEED_
FREQ_REF Hz
0.0
RW Num
US
P1 Rotary Lines Per Revolution
{03.034}
1 to 100000
1024
4096
RW Num
US
00.028
Enable Auxiliary Key
{06.013}
Disabled (0), Forward/Reverse (1), Run Reverse (2)
Disabled (0)
RW
Txt
US
00.029
NV Media Card File Previously
Loaded
{11.036}
0 to 999
RO Num
NC PT
Summary of Contents for Digitax HD M753 EtherCAT
Page 261: ......
Page 262: ...0478 0461 03...