manualshive.com logo in svg

Multitech MTCBA-C-IP-N1, Reference Manual, Page: 87 / 202

Share
Download
Multitech MTCBA-C-IP-N1 Reference Manual Download Page 87

Chapter 13 – Specific AT Commands 

 

Multi-Tech Systems, Inc. CDMA Wireless AT Commands (PN S000294J) 

87 

 

Minute Alert  +WMBP 

 

Description:

  

This command is used to set the minute alert while in a voice conversation. 

 

Values: 

 

<mode> 

 

0 

Disable alert 

 

1 

Enable alert  

 

<interval> 

 

1 – 30     

Time in minutes 

 

Syntax:

  

Command syntax:

 AT+WMBP=<mode>,<interval> 

 

Command 

 

Possible Responses 

 

AT+WMBP=0 

 

Note: Turn off the alert 

 

OK 

 

AT+WMBP=1,4 

 

Note: Turn on the alert and set 4 minutes apart 

 

OK 

 

AT+WMBP? 

 

Note: Request current setting 

 

+WMBP: 1,4 

 

AT+WMBP=? 

 

Note: Display valid parameter ranges. 

 

+WMBP: (0-1),(1-30) 

 

 
 

Configure LED Indicator  +CLED 

 

Description:

  

This command is used to configure GPIO 41 and GPIO 54 for general purpose use. The default use of these 
two GPIO’s is to drive LED indicators on the Developer Kit board. This command allows a user application to 
disable this default behavior. When disabled, the user application has full control over the state of these 
GPIO’s. The modem operating software will be prevented from change them for operational status 
indications.  

 

The byte value specified with the +CLED command is a bitmap where bit 0 configures LED1/GPIO 41 and 
bit 1 configures LED2/GPIO 54. Bit positions 2 through 7 are ignored.  

 

The state of the +CLED specified control bits is not persistent. Both bit positions are always set active (1) 
during boot resulting in LED status indicator operation. The +CLED command must be used by the user 
application after each boot if GPIO 41 or GPIO 54 are used for other purposes.  

Values:  

<bitmap value> 

 

bit 0 

0 = GPIO 41 selected; 1 = LED1 selected. 

 

bit 1 

0 = GPIO 54 selected; 1 = LED2 selected.  

bit 2 – bit7

 Reserved 

 

Syntax:

  

Command syntax:

 AT+CLED=<bitmap value> 

 

Command 

Possible Responses 

AT+CLED? 

 

Note: Display current settings. 

 

CLED: 3 

 

OK 

 

Note: Both GPIO’s are used for modem operational status 
indicators. 

 

AT+CLED=? 

 

Note: Display valid parameter range. 

 

CLED: (0-3) 

 

OK 

 

AT+CLED=1 

 

Note: Set bit 1 to inactive and bit 0 to active. 

 

 
AT+WIOW=54,0 

 

Note: Set GPIO state. 
 
AT+WIOR=41 

 

Note: Read state of LED1 indicator. 

 

 

OK 

 

Note: GPIO 54 available, LED1 used for modem status. 

 

 
OK 

 

Note: Set GPIO 54 to 0. 

 

 
+WIOR: 1 

 

OK 

 

Note: Read current state of LED1 indicator

 

AT+CLED=2 

 

Note: Set bit 1 to active and bit 0 to inactive.  
 
AT+WIOW=41,1 

 

Note: Set GPIO state.  
 
AT+WIOW=54,1 

 

Note: Set LED2 state. 

 

 

OK 
Note: LED2 used for modem status, GPIO 41 available.  
 
OK 

 

Note: Set GPIO 41 to 1.  
 
OK 

 

Note: LED2 indicator set to “on”. LED on/off state may 
change due to modem status indication.

 

 

Summary of Contents for MTCBA-C-IP-N1











































































































































































































Reviews:

No comments