Multitech MTCBA-C-IP-N1 Reference Manual Download Page 28

Page: 28 / 202

Chapter 4 – Call Control Commands

Multi-Tech Systems, Inc. CDMA Wireless AT Commands (PN S000294J)

Side Tone Modification +SIDET

Description:

This command is used to set the level of

audio feedback

in the speaker (microphone feedback in the

speaker).

Values:

<val1>

Sidetone is disabled

Sidetone is enabled

<val2>

No side tone

Handset Sidetone levels

Headset Sidetone levels

Max Sidetone level

Syntax:

Command syntax:

AT+SIDET=<val1>,<val2>

Command

Possible Responses

AT+SIDET=1,0

Note: Command valid

AT+SIDET?

Note: Current value

+SIDET: 1,0

Note: Command valid

Initialize Voice Parameters +VIP

Description:

This command allows voice parameters to be restored from NV memory.

Values:

Gain controls are restored (+VGT and +VGR)

Voice path selection is restored (+SPEAKER)

Echo cancellation is restored (+ECHO)

Sidetone values are restored (+SIDET)

Syntax:

Command syntax:

AT+VIP

Command

Possible Responses

AT+VIP

Note: Command valid

TTY Mode +WTTY

Description:

This command enables TTY mode on the headset audio path. The modem must be in a voice call to set this
command, and when the call ends it goes back to standard audio mode.

Syntax:

Command syntax:

AT+WTTY

Command

Possible Responses

AT+WTTY

Note: Command valid

Summary of Contents for MTCBA-C-IP-N1











































































































































































































Search results

Summary of Contents for MTCBA-C-IP-N1

Reviews:

Multitech MTCBA-C-IP-N1, Reference Manual, Page: 28 / 202

Search results

Summary of Contents for MTCBA-C-IP-N1

Reviews: