Multitech MTCBA-C-IP-N1 Reference Manual Download Page 18

Page: 18 / 202

Chapter 3 – General Commands

Multi-Tech Systems, Inc. CDMA Wireless AT Commands (PN S000294J)

Ringer Sound Level +CRSL

Description

This command is used to set/get the sound level of the ringer on incoming calls.

Values:

<sound level>

Min volume (muted)

Default volume (default)

Max volume

Syntax:

Command syntax: AT+CRSL=<sound Level>

Command

Possible Responses

AT+CRSL=0

Note: Set volume to Min (muted).

Note: Current ring playing is muted.

AT+CRSL=4

Note: Set volume to Max.

OK
Note: Current ring playing with Max. volume.

AT+CRSL?

Note: Get current ringer sound level

CRSL:4
OK
Note: Current level is 4

AT+CRSL=4
Note: Supported parameters

CRSL: (0-4)
OK

Subscriber Number +CNUM

Description:

This command is used to return the subscriber MSISDN. If the subscriber has different MSISDNs for
different services, each MSISDN is returned on a separate line.

Values:

<alphax>

optional alphanumeric string associated with <numberx>

<numberx>

string type phone number with format as specified by <typex>

<typex>

type of address byte in integer format – only supports 129

Syntax

Command syntax:

AT+CNUM

Ruim command syntax:

AT+CNUM=<number> (RUIM software releases only)

Response syntax:

+CNUM: <alpha1>, <number1>, <type1>, <CR><LF>+CNUM: <alpha2>, <number2>,

<type2> …

Command

Possible Responses

AT+CNUM

Note: Get MSISDN

+CNUM :“Phone”,”8585551212”,129

Note: MSISDNs

AT+CNUM=?

+CNUM:

AT+CNUM=8585551212
Note: Set module phone number in RUIM software
releases. Entry of the SPC is not required.

OK

Note: New number set.

Note:

For RUIM software releases, this command provides a means for setting the phone number without the need to have

previously entered the SPC (+WSPC command). The value for <number> can be up to 15 digits. The use of this command
does not effect the IMSI.

Select Type of Address +CSTA

Description:

This command is used to select the type of phone address to use.

Values

<typex>

type of address byte in integer format – only supports 129

Syntax:

Command syntax: AT+CSTA=<typex>

Command

Possible Responses

AT+CSTA?

Note: Get type of address

+CSTA: 129

Note: Local Number format

AT+CSTA=?

Note: Get supported address types

+CSTA: (129-129)

Summary of Contents for MTCBA-C-IP-N1











































































































































































































Search results

Summary of Contents for MTCBA-C-IP-N1

Reviews:

Multitech MTCBA-C-IP-N1, Reference Manual, Page: 18 / 202

Search results

Summary of Contents for MTCBA-C-IP-N1

Reviews: