manualshive.com logo in svg

Multitech MTCBA-C-IP-N1, Reference Manual, Page: 167 / 202

Share
Download
Multitech MTCBA-C-IP-N1 Reference Manual Download Page 167

Chapter 21 – Unsolicited AT Result Codes 

 

Multi-Tech Systems, Inc. CDMA Wireless AT Commands (PN S000294J) 

167 

 

Emergency Mode  +WSOS 

 

Description:

  

This unsolicited response indicates a change in the status of Emergency Mode has taken place. In the event 
that Emergency Mode is entered as the result of an emergency call, this response will be sent to indicate 
that the modem is now in emergency mode. After this point, to exit the modem out of Emergency Mode, an 
AT+WSOS or AT+COPS command must be sent, which will result in a +WSOS response to confirm that 
Emergency Mode has been exited. See +WSOS, section for more information about Emergency Mode.  

 

Values:

  

The parameters values are the following ones: 

 

 

<flag> 

 

0 

Emergency Mode Exited 

 

1 

Emergency Mode Entered  

 

Syntax:

 

 

Response Syntax: +WSOS: <flag>  

Command 

Possible Responses 

ATD911; 
Note: Make emergency call  

OK 
+WSOS:1 

 

+WORG:911 

 

Note: UnsolWSOS result confirms Emergency 
Mode is entered  

AT+WSOS 

 

Note: Exit Emergency Mode 

 

OK 

 

+WSOS:0 

 

Note: UnsolWSOS result confirms Emergency 
Mode is exited 

 

AT+COPS=0,0 

 

Note: While in Emergency Mode, the mode 
preference is changed, resulting in Emergency 
Mode being exited 

 

OK 

 

+WSOS:0 

 

+COPS:0,0 

 

Note: UnsolWSOS result confirms emergency 
mode exited and unsolCOPS result confirms 
Automatic mode is requested 

 

 
 
 

Current NAM Change  +WNAM 

 

Description:

  

This response indicates that the current NAM has changed. 

 

 
Syntax:   

Response Syntax: +WNAM: <nam> 

 

Command 

 

Possible Responses 

 

 +WNAM:2 

 

 

<nam> 

 

1

 NAM 

1 

 

2 

NAM 2 

 

3 

NAM 3 

 

4 

NAM 4  

Summary of Contents for MTCBA-C-IP-N1











































































































































































































Reviews:

No comments