Home
/
Multitech
/
MTCBA-C-IP-N1
/
Reference Manual

Multitech MTCBA-C-IP-N1, Reference Manual, Page: 125 / 202

Share

Page: 125 / 202

Multitech MTCBA-C-IP-N1 Reference Manual Download Page 125

Chapter 18 – Qualcomm Defined AT Commands for CDMA Operation

Multi-Tech Systems, Inc. CDMA Wireless AT Commands (PN S000294J)

125

Chapter 18 – Qualcomm

Defined AT Commands for

CDMA Operation

This section contains AT commands that are specified and developed by Qualcomm.

Note:

Mobile IP related AT commands work only on the modems that supported the MIP features.

Transition to Diagnostics Monitor $QCDMG

Description:

This command returns “OK” and then transitions the phone serial port to DM mode. DM mode runs at 38.4
Kbps and uses a proprietary half-duplex protocol.

Syntax:

Command syntax:

AT$QCDMG

Command

Possible Responses

AT$QCDMG

Note: Transition to DM port

OK

Note: Command is valid

Quick Net Connect $QCQNC

Description:

This command is used to enable or disable the Quick Net Connect (QNC) feature.

Values:

<Val>

0

Disable QNC capability. This means that packet Originations will use the Packet Data Service Option
number.

1

Enable QNC capability. This means that Packet Originations will use the Async Data Service Option
number.

Syntax

:

Command syntax:

AT$QCQNC=<Val>

Command

Possible Responses

AT$QCQNC?

Note: Display the current setting

$QCQNC: 0

OK Note: Command is valid

AT$QCQNC=?

Note: Display the range of values

$QCQNC: (0-1)

OK Note: Command is valid

AT$QCQNC=1

Note: Enable QNC compatibility

OK
Note: Command is valid

Protocol Revision in Use $QCPREV

Description:

This command is used to query the protocol revision in use.

Values:

The command will return one of the following codes:

1

JST008

3

IS-95A

4

IS-95B

6

IS-2000

Syntax:

Command syntax:

AT$QCPREV

Command

Possible Responses

AT$QCPREV?

Note: Display the current setting

ERROR

Note: Command is not valid

AT$QCPREV

Note: Display the of value

$QCPREV: 6

OK

Note: Command is valid

«
...
123
124
125
126
127
...
»

Summary of Contents for MTCBA-C-IP-N1











































































































































































































Reviews:

No comments