manualshive.com logo in svg

Multitech MTCBA-C-IP-N1, Reference Manual, Page: 126 / 202

Share
Download
Multitech MTCBA-C-IP-N1 Reference Manual Download Page 126

Chapter 18 – Qualcomm Defined AT Commands for CDMA Operation 

 

Multi-Tech Systems, Inc. CDMA Wireless AT Commands (PN S000294J) 

126 

 

Originate M-to-M Packet Data Call  $QCMTOM 

 

Description:

  

This command is used to originate a Mobile-to-Mobile Packet Data call using the QUALCOMM proprietary 
Service Option number. 

  

 

Values:  

<number> 

 

 where 

<number>

 is the phone number to dial. This command will originate a Mobile-to-Mobile Packet data 

call using the QUALCOMM-proprietary Service Option number 0x8003. This is a Rate Set 1 call. 

 

Syntax:

  

Command syntax:

 AT$QCMTOM = ‘’<number>’’ 

 

Command 

 

Possible Responses 

 

AT$QCMTOM? 

 

Note: Display the current setting 

 

$QCMTOM: “” 

 

OK 

 

Note: Command is valid 

 

AT$QCMTOM =? 

 

Note: Display the range of values 

 

$QCMTOM: (20,21,23-7E) 

 

OK 

 

Note: Command is valid 

 

AT$QCMTOM =”#777” 

 

Note: Packet data call to the number 

 

OK 

 

Note: Command is valid 

 

 
 

Dump RLP Protocol Statistics  $QCRLPD 

 

Description:

  

This command is used to dump the RLP statistics in ASCII format to the DTE. This does not apply to RLP 3 
statistics (see $QCRL3D). 

 

 

Syntax:

  

Command syntax:

 AT$QCRLPD 

 

Command 

 

Possible Responses 

 

AT$QCRLPD? 

 

Note: Display the current setting 

 

ERROR 

 

Note: Command is not valid 

 

AT$QCRLPD 

 

Note: Dump RLP statistics data 

 

$QCRLPD: 

 

Rx Data Cnt :0000 Tx Data Cnt :0000 

 

…. 

 

OK 

 

Note: Command is valid 

 

 
 

Reset RLP Protocol Statistics  $QCRLPR 

 

Description:

  

This command is used to zero all the RLP statistics counters. This does not apply to RLP 3 statistics (see 
$QCRL3R). 

 

 

Syntax:

  

Command syntax:

 AT$QCRLPR 

 

Command 

 

Possible Responses 

 

AT$QCRLPR? 

 

Note: Display the current setting 

 

ERROR 

 

Note: Command is not valid 

 

AT$QCRLPR 

 

Note: Reset RLP statistics counter 

 

$QCRLPR: 

 

OK 

 

Note: Command is valid 

 

 

Dump PPP Protocol Statistics  $QCPPPD 

 

Description:

  

This command is used to dump the PPP statistics in ASCII format to the DTE. 

 

Syntax:

  

Command syntax:

 AT$QCPPPD 

 

 

Command 

 

Possible Responses 

 

AT$QCPPPD? 

 

Note: Display the current setting 

 

ERROR 

 

Note: Command is not valid 

 

AT$QCPPPD 

 

Note: Dump PPP statistics information 

 

$QCPPPD: 

 

In LCP :0000 Out LCP :0000 

 

…. 

 

OK 

 

Note: Command is valid 

 

Summary of Contents for MTCBA-C-IP-N1











































































































































































































Reviews:

No comments