manualshive.com logo in svg

Multitech MTCBA-C-IP-N1, Reference Manual, Page: 187 / 202

Share
Download
Multitech MTCBA-C-IP-N1 Reference Manual Download Page 187

Chapter 23 – Verizon® Specific AT Commands 

 

Multi-Tech Systems, Inc. CDMA Wireless AT Commands (PN S000294J) 

187 

 

Commit Successful  +WOTC 

 

Description:

  

This Over-The-Air Service Provisioning (OTASP) response indicates that the programmed parameters have 
be successfully committed to NVRAM. 

 

Syntax:

  

Response Syntax:

 +WOTC: “Commit Successful” 

 

Possible Responses 

 

+WOTC: “Commit Successful” 

 

 

SPL Unlocked  +WOTS 

 

Description:

  

This Over-The-Air Service Provisioning (OTASP) response indicates that the Software Provisioning Lock is 
in the unlocked state. 

 

Syntax:

  

Response Syntax: 

+WOTS: “SPL unlocked” 

 

Possible Responses 

 

+WOTS: “SPL unlocked” 

 

 

NAM Download OK  +WOTN 

 

Description:

  

This Over-The-Air Service Provisioning (OTASP) response indicates that the NAM download has completed 
successfully. 

 

Syntax:

  

Response Syntax: 

+WOTN: “NAM Download OK” 

 

Possible Responses 

 

+WOTN: “NAM Download OK” 

 

 

MDM Download OK  +WOTM 

 

Description:

  

This Over-The-Air Service Provisioning (OTASP) response indicates that the MDM download has completed 
successfully. 

 

Syntax:

  

Response Syntax:

 +WOTM: “MDM Download OK” 

 

Possible Responses 

 

+WOTM: “MDM Download OK” 

 

 

MSI Download OK  +WOTI 

 

Description:

  

This Over-The-Air Service Provisioning (OTASP) response indicates that the IMSI download has completed 
successfully. 

 

Syntax:

  

Response Syntax:

 +WOTI: “IMSI Download OK” 

 

Possible Responses 

 

+WOTI: “IMSI Download OK” 

 

 

PRL Download OK  +WOTP 

 

Description:

  

This Over-The-Air Service Provisioning (OTASP) response indicates that the PRL download has completed 
successfully.

  

 

Syntax:

  

Response Syntax: 

+WOTP: “PRL Download OK” 

 

Possible Responses 

 

+WOTP: “PRL Download OK” 

 

 

Excess SPC Failures  +WLCK 

 

Description:

  

This response indicates that 15 failed attempts have been made to enter the service programming code. If 
the modem is not in emergency mode, any active call will be terminated and the modem will go into offline 
mode. 

  

 

Note:

  

A successfully entered service programming code grants access to modem configuration data. 

 

Syntax:

  

Response Syntax:

 +WLCK: “Excess SPC failures!” 

 

Command 

 

Possible Responses 

 

AT+WSPC=0,123456 

 

Note: 15

th 

attempt to enter the SPC. 

 

+WLCK: “Excess SPC failures!” 

 

Note: Modem now in offline mode. 

 

 

Summary of Contents for MTCBA-C-IP-N1











































































































































































































Reviews:

No comments