manualshive.com logo in svg

Multitech MTCBA-C-IP-N1, Reference Manual, Page: 71 / 202

Share
Download
Multitech MTCBA-C-IP-N1 Reference Manual Download Page 71

Chapter 12 – Postion Determination (GPS) Commands 

 

Multi-Tech Systems, Inc. CDMA Wireless AT Commands (PN S000294J) 

71 

 

Position Determination Transport Setting  +WPTLM 

 

Description:  

This command specifies the transport layer to be used for the position determination session. The transport 
layer is carrier specific and may require other PD parameters (IP address, IP port) to also be configured.  

Values:  

<setting> 

 

0 

TCP/IP - Use a TCP/IP based socket for PDE/MS PD data exchanges.  

1 

DBM - Use data burse messages for PDE/MS PD data exchanges.  

Note: 

For software versions earlier than v3.0, when a tracking mode is requested (continuous position fixes) 

and the TCP/IP transport layer is used, position fixes will not be delivered until the data call ends. Then, only 
the last 10 position fixes will be presented.  

Syntax:  

Command syntax: 

AT+WPTLM=<setting>  

Command 

 

Possible responses 

 

AT+WPTLM=?  
Note: Display valid parameter range.  

+WPTLM: (0-1)  
OK  

AT+WPTLM?  
Note: Display current setting.  

+WPTLM: 1  
OK  

AT+WPTLM=0  
Note: Set the transport setting to TCP/IP  

OK  
Note: Command accepted.  

 
 

Set Position Determination IP Address  +WPDIP 

 

Description:  

This command is used to set the IP address for the position determination session. A valid IP address is 
required if the TCP/IP transport layer is used.  

Values:  

<ip_address> 

 

 

Specified in standard IP address format xxx

.

xxx

.

xxx

.

xxx where xxx is 000 to 255. This is a carrier specific 

value.  

Syntax:  

Command syntax: 

AT+WPDIP=<ip_address>  

Command 

 

Possible responses 

 

AT+WPDIP?  
Note: Query current PD IP address.  

+WPDIP:192.168.135.124  
OK  

AT+WPDIP=192.168.135.124  
Note: Set PD IP address.  

OK  
Note: New PD IP address set.  

 
 

Set Position Determination Port ID  +WPDPT  

Description:  

This command is used to set the port ID value for the position determination session. A valid port ID value is 
required if the TCP/IP transport layer is used.  

Values:  

<port_id> 

 

 

Numeric value in the range 0 to 65535. Value is carrier specific.  

Syntax :  

Command syntax: 

AT+WPDIP=<port_id>  

Command 

 

Possible responses 

 

AT+WPDPT?  
Note: Query current PD port id value.  

+WPDPT: 4911  
OK  

AT+WPDPT=4911  
Note: Set PD port id value.  

OK  
Note: New PD port id value set.  

 

Summary of Contents for MTCBA-C-IP-N1











































































































































































































Reviews:

No comments