manualshive.com logo in svg

Multitech MTCBA-C-IP-N1, Reference Manual, Page: 113 / 202

Share
Download
Multitech MTCBA-C-IP-N1 Reference Manual Download Page 113

Chapter 16 – Extended AT Commands in IS707.3 

 

Multi-Tech Systems, Inc. CDMA Wireless AT Commands (PN S000294J) 

113 

 

Modulation Selection  +MS 

 

Description:

  

The extended-format compound parameter is used to control the manner of operation of the modulation 
capabilities in the DCE. 

 

 

Values:  

<carrier>    

 

 

manufacturer specific 

 

 <automode> 

 

  

0 

Disabled 

 

  

1 

enabled with V.8 or V.32bis Annex where applicable 

 

 

<min_rate> & <min_rx_rate>  

 

 

  set to 0 if unspecified 

 

 

<max_rate> & <max_rx_rate> 

 

 

  set to 0 if unspecified 

 

 

Syntax:

  

Command syntax: 

AT+MS=[<carrier>[,<automode>[,<min_rate>[,<max_rate>[,<min_rx_rate> 

[,<max_rx_rate>]]]]]] 

 

Command 

 

Possible Responses 

 

AT+MS? 

 

Note: Display the parameter information. 

 

+MS: V32B,1,1200,14400 

 

Note: Command is valid 

 

AT+MS=? 

 

Note: Display the range of parameters 

 

+MS: (V21,V22),(0,1,),(0,300-14400),(0,300-14400) 

 

Note: Command is valid 

 

AT+MS=V21,1,1200,2400,1200,2400  
Note: Display the range of parameters  

 OK  
Note: Command is valid  

 

 

Modulation Automode Control  +MA 

 

Description:

  

The extended-format compound parameter is a list of modulations that the DCE may use to connect with the 
remote DCE in automode operation, for answering or originating data calls. 

 

 

Syntax:

  

Command syntax:

 AT+MA=[<carrier>[,<carrier>[,<carrier>[,…]]]] 

 

Command 

 

Possible Responses 

 

AT+MA? 

 

Note: Display the parameter information. 

 

+MA: V32, V32B 

 

Note: Command is valid 

 

AT+MA=? 

 

Note: Display the range of parameters 

 

+MA: (V32B,V32,V26B,V22B,V22,V21) 

 

Note: Command is valid 

 

AT+MA=V32 

 

Note: Set to V32 

 

OK 

 

Note: Command is valid 

 

 
 

Modulation Reporting Control  +MR 

 

Description:

  

The extended-format numeric parameter controls whether the extended-MCR:<carrier> and 
+MRR:<rate> intermediate result codes are transmitted from the IWF to the mobile station. 

 

 

Values:  

<Val> 

 

  

0 

Disables reporting of modulation connection 

 

  

1 

Enables reporting of modulation connection (+MCR and +MRR are transmitted) 

 

 

Syntax:

  

Command syntax:

 AT+MR=[<Val>] 

 

Command 

 

Possible Responses 

 

AT+MR? 

 

Note: Display the current setting. 

 

+MR: 0 

 

Note: Command is valid 

 

AT+MR=? 

 

Note: Display the range of setting. 

 

+MR: (0,1) 

 

Note: Command is valid 

 

AT+MR=1 

 

Note: Enable reporting. 

 

OK 

 

Note: Command is valid 

 

 

Summary of Contents for MTCBA-C-IP-N1











































































































































































































Reviews:

No comments