manualshive.com logo in svg

Multitech MTCBA-C-IP-N1, Reference Manual, Page: 168 / 202

Share
Download
Multitech MTCBA-C-IP-N1 Reference Manual Download Page 168

Chapter 21 – Unsolicited AT Result Codes 

 

Multi-Tech Systems, Inc. CDMA Wireless AT Commands (PN S000294J) 

168 

 

Voice Mail Indicator  +WVMI 

 

Description:

  

This response indicates the status of the Voicemail Inbox. 

 

Syntax: 

 

Response syntax: +WVMI: <LineId>,<Num> 

 

Command 

 

Possible Responses 

 

 +WVMI: 

1,2 

 

OK 

 

Note: 2 messages are in your voicemail box. 

 

Values: 

 

<LineId> 

 

 1 

Line 1 

 

 

<Num>  

 The number of messages waiting in the inbox. Maximum value is 99. 

 

0 

No message waiting. 

 

1 

One message is waiting 

 

3 

Three messages are waiting 

 

Example: 

 

AT+CPHS?  

 

Interrogate the status of CPHS functionality 

 

+CPHS: 1,0  

 

The voice mail indicator functionality is deactivated 

 

OK 

 

AT+CPHS=3,1    

Syntax error 

 

+CME ERROR:   

3 

 

AT+CPHS=1,1    

Activate the voice mail indicator functionality 

 

OK 

 

AT+CPHS?  

 

Interrogate the status of CPHS functionality 

 

+CPHS: 1,1  

 

The voice mail indicator functionality is activated 

 

OK  

**** the message box contains 1 message *****  

+WVMI: 1,1  

 

A message is waiting on Line 1 

 

AT+CPHS=2,1  

 

Interrogate the status of voice mail indicator functionality 

 

OK 

 

+WVMI: 1,1  

 

A message is waiting on LINE 1 

 

AT+CPHS?  

 

Interrogate the status of CPHS functionality 

 

+CPHS: 1,1  

 

The voice mail indicator functionality is activated 

 

OK 

 

 
 

SMS Message Storage Full  +WMGF 

 

Description:  

This response indicates that the SMS Service Center has attempted to send an SMS message but it was 
rejected because SMS Message Storage is Full. No new SMS messages will be received until some room is 
created by deleting old messages from SMS storage. Message deletion can be done using AT+CMGD.  

Syntax:

  

Response Syntax: +WMGF 

 

Example Result 

 

+WMGF 

 

Note: Incoming message rejected. Message center notified with “out of resources” message. Message 
center will attempt to re-send the message at a later time. 

 

 
 

Power Save  +WSPS 

 

Description:

  

This response is output whenever a change occurs in the power save status. The +WSPS: 1 response 
indicates that the module is unable to obtain a radio network connection and is temporarily suspending its 
search. This suspend mode lasts for about 3 minutes. The +WSPS: 0 response indicates that the module is 
again actively searching for a radio network connection. This feature helps to conserve battery power in 
cases where coverage is marginal.   

 

Note:

 This response is not used in Verizon software versions.  

Syntax:

 

 

Response Syntax: +WSPS: <state> 

 

Command 

 

Possible responses 

 

 +WSPS: 

1 

 

Note: Entering power save mode. 

 

 

+WSPS: 0          
Note: Leaving power save mode.

 

AT+WSPS? 

 

Note: Display current power mode state. 

 

+WSPS: 0 

 

OK                    Note: Not in power save mode. 

 

 

<state> 

 

0 

Leaving power save 

 

1 

Entering power save  

Summary of Contents for MTCBA-C-IP-N1











































































































































































































Reviews:

No comments