Multitech MTCBA-C-IP-N1 Reference Manual Download Page 63

Chapter 11 – Phone Book Commands 

 

Multi-Tech Systems, Inc. CDMA Wireless AT Commands (PN S000294J) 

63 

 

Chapter 11 – Phone Book 

Commands 

 

 
In this chapter, the AT commands are used to operate on mobile phonebook. These phonebook commands adhere to the set 
defined in GSM 07.07 specification. Please refer to GSM 07.07 for further AT command usage and description.  
 
For all phonebook read commands (+CPBR, +CPBF, +CPBP), the TON/NPI MSB of each number is set to 1 (ex: a TON/NPI 
stored as 17 is displayed as 145). 

 

 
When accessing numbers in the call history phonebooks (“LD”, “MC”, or “RC”), if a matching number is found in one of the 
other phonebooks, the text portion of the matching entry is copied to the call history entry.  
 
The phone book “SM” is only supported in an RUIM capable modem.  
 
When an RUIM is present, the “MT” phonebook is a combination of two phonebooks as shown in the example below. This 
must be taken into account when using a phone book AT command index to access an entry in this phonebook.  
 

ME 

Æ

 

Index range 1 to 100 

 

SM 

Æ

 

Index range 1 to 150 (SIM card) 

 

MT 

Æ

 

ME start at 1, SM start at 101 (SIM card) 

 

< - - - - - - - ME - - - - - - -> < - - - - - - - SM - - - - - - - - -> 

 

1  

100    101  

250 

 

 
 

Select Phonebook Memory Storage  +CPBS 

 

Description:

  

This command selects the type of memory where the phonebook will be stored. Possible phone books are 
listed below under the 

<bk> 

section. If there’s no RUIM card present, selecting “SM” phonebook returns 

ERROR.  

Values:  

<bk>  

“SM” 

ADN (RUIM phonebook) 

 

“ME” 

ME (ME NV phonebook) 

 

“LD” 

LND (ME or RUIM last dialed phonebook; depending on presence of RUIM) 

 

“EN” 

EN (ME NV emergency numbers) 

 

“MC” 

MSD (ME missed calls list) 

 

“MT” 

MT (combined ME and RUIM phonebook) 

 

“RC” 

LIC (ME received calls list) 

 

“FD” 

FDN (SIM Fix Dialing, restricted phonebook) 

 

Syntax:

  

Command syntax:

 AT+CPBS=”<bk>” 

 

Command 

 

Possible responses 

 

AT+CPBS=? 

 

Note: Possible values, not all may be supported 

 

+CPBS: (“ME”,”MC”,”LD”,”RC”,”EN”) 

 

Note: Not all may be supported 

 

AT+CPBS=”EN” 

 

Note: Select the emergency phonebook 

 

OK 

 

Note: Emergency phonebook selected 

 

AT+CPBS? 

 

Note: Return the currently selected phonebook 

 

+CPBS: EN,0,9 

 

OK 

 

Note: EN phonebook selected, 0 locations used, 9 
available 

 

AT+CPBS=”MT” 

 

Note: Select the MT phonebook (RUIM present). 

 

AT+CPBS? 

 

OK 

 

Note: MT phonebook selected 

 

+CPBS: MT,5,300 

 

Note: Display MT phonebook information. Combination 
of ME and SM phonebooks. 

 

OK 

 

Note: 5 locations used, 300 available (combination 
of ME and RUIM phonebooks). 

 

 

Summary of Contents for MTCBA-C-IP-N1











































































































































































































Reviews: