manualshive.com logo in svg

Multitech MTCBA-C-IP-N1, Reference Manual, Page: 74 / 202

Share
Download
Multitech MTCBA-C-IP-N1 Reference Manual Download Page 74

Chapter 13 – Specific AT Commands 

 

Multi-Tech Systems, Inc. CDMA Wireless AT Commands (PN S000294J) 

74 

 

Chapter 13 - Specific AT 

Commands 

 

 

Manufacturer Identification  +WGMI 

 

Description:

  

This command gives the manufacturer identification.  

 

Syntax: 

 

Command syntax: 

AT+WGMI 

 

Command 

 

Possible Responses 

 

AT+WGMI 

 

Note: Get manufacturer identification 

 

+WGMI: MODEM 

 

OK 

 

Note: Command valid, modem 

 

 

Request Model Identification  +WGMM 

 

Description

:  

This command is used to get the supported frequency bands. With multi-band products the response may 
be a combination of different bands.  

 

Syntax:

  

Command syntax:

 AT+WGMM 

 

Command 

 

Possible Responses 

 

AT+WGMM 

 

Note: Get supported bands 

 

+WGMM: 800 1900 

 

OK 

 

Note: CDMA 800 MHz band and 1900 (PCS) 

 

 

Summary of Contents for MTCBA-C-IP-N1











































































































































































































Reviews:

No comments