Motorola PMP 320 Hardware Installation Download

Page: 25 / 146

PMP320HDW2v1

1-25

Preliminary

JUL 2010

What is included when the CMM4 unit is shipped

Chapter 1: Product Description

What is included when the CMM4 unit is shipped

The CMM4 as shipped includes:

•

Weatherized enclosure containing the controller board, EtherWAN Ethernet Switch, and

GPS coax surge suppressor

•

Patch cables between the controller board and the EtherWAN Ethernet Switch

•

U-bolts and V-brackets for pole-mounting the CMM4

•

GPS Antenna

•

GPS antenna pole-mount kit

•

A 1-hole cable gland insert for use on the DC power cable

The CMM4 as shipped does not include:

•

Any power supply. The appropriate power supply(s), 30 VDC and/or 56 VDC, must be

ordered separately

•

Ethernet cables to connect the CMM4 to APs, backhauls, or terrestrial feeds

•

Coax cable connecting the CMM4 to the GPS antenna

•

DC power line cables are not provided (AC power line cables are not included with the

power supplies)

Summary of Contents for PMP 320


















































































































































Search results

Summary of Contents for PMP 320

Reviews:

Related manuals for PMP 320

Brands by name

Popular brands

Motorola PMP 320, Hardware Installation

Search results

Summary of Contents for PMP 320

Reviews:

Related manuals for PMP 320

Brands by name

Popular brands