Motorola PMP 320 Hardware Installation Download

Page: 47 / 146

PMP320HDW2v1

2-17

Preliminary

JUL 2010

PMP 320 Hardware Installation

Attach the AP assembly to a pole

NOTE

•

The L-COM surge suppressor is used if the Gigabit Ethernet port is used in

the CMM4. The L-COM when used is installed either in the CMM4 cabinet, or
installed inside the communications building.

•

This figure shows the GPS near the top of the AP unit. For installation

information about the GPS refer to

Installing the GPS Antenna on page 3-7

•

The AC line cord is not provided with the hardware.

This figure shows the GPS near the top of the AP unit. For installation information about the
GPS refer to

Installing the GPS Antenna on page 3-7

Procedure 2-3 Attaching the AP assembly to a pole

Using standard work and safety practices for tower climbing, connect the

assembled unit (assembled antenna, brackets and radio) to a pole, mounting
fixture, or a tower. The unit must be mounted to avoid accidental touching
by personnel. The standard mounting height is typically at least 4 m (13
ft) above ground level.

Pole Is Shown

For Reference

Antenna

Radio

(Secured on Antenna)

DIV connector

MAIN connector

Ethernet

NOTE

Approximate cable distance between the AP and the CMM4 is 100
meters.

Continued

Summary of Contents for PMP 320


















































































































































Search results

Summary of Contents for PMP 320

Reviews:

Related manuals for PMP 320

Brands by name

Popular brands

Motorola PMP 320, Hardware Installation

Search results

Summary of Contents for PMP 320

Reviews:

Related manuals for PMP 320

Brands by name

Popular brands