Motorola PMP 320 Hardware Installation Download

Page: 102 / 146

5-18

PMP320HDW2v1

Preliminary

JUL 2010

Connecting the power supply and the Ethernet cable to the computer

Chapter 5: CSM Hardware Installation

Procedure 5-11 Connecting the power supply

Plug the category 5e cord from the CSM/surge suppressor into the jack labeled

AC Power

on the CSM Power Injector (if this connection is not already made).

Connect the protected side of the 600SSD surge suppressor cable to the

Data

& Power Out

port of the CSM power injector.

Use a standard category 5e Ethernet cable to connect the computer to the
jack labeled

computer

on the power supply.

NOTE

The cable to the CSM provides both power and Ethernet connection.
It is not pin or voltage compatible with

IEE std.802.3af-2003

power over Ethernet.

The power cord uses standard household power. Plug the power cord in the
AC power source.

NOTE

The AC line cord is not provided with the hardware. Acquire the
appropriate power line cord for the country where the unit is
installed.

Figure 6-8

illustrates the cable connection through the data line protector and into the power

supply cord.

Summary of Contents for PMP 320


















































































































































Search results

Summary of Contents for PMP 320

Reviews:

Related manuals for PMP 320

Brands by name

Popular brands

Motorola PMP 320, Hardware Installation

Search results

Summary of Contents for PMP 320

Reviews:

Related manuals for PMP 320

Brands by name

Popular brands