Motorola PMP 320 Hardware Installation Download

Page: 45 / 146

PMP320HDW2v1

2-15

Preliminary

JUL 2010

LED indicator

Chapter 2: AP Hardware Installation

LED indicator

The LED display for the AP are either Green or off.

Figure 2-3 LED location diagram

Table 2-2 LED indicators for the AP

LED

Description

PWR (D14)

Power – green indicates the DC power

is on. This LED indicates that

the board is powered on.

SYN/1 (D13)

Synchronization indicator – this indicator is
on whenever the AP is synchronized with the
GPS, or when ever the GPS is not used at all.

SES/2 (D12)

Not used, but is always ON.

LNK/5 (D9)

GMAC Ethernet – the LED is on when

the GMAC Ethernet link is up.

ACT/4 (D10)

Activity – indicates activity on the ENET port.

GPS/3 (D11)

GPS pulse indicator – this LED is

on every 1 pps interrupt, and turned off

20 frames after 100 milliseconds).

Summary of Contents for PMP 320


















































































































































Search results

Summary of Contents for PMP 320

Reviews:

Related manuals for PMP 320

Brands by name

Popular brands

Motorola PMP 320, Hardware Installation

Search results

Summary of Contents for PMP 320

Reviews:

Related manuals for PMP 320

Brands by name

Popular brands