Motorola PMP 320 Hardware Installation Download | Manualshive

Page: 38 / 146

background image

2-8

PMP320HDW2v1

Preliminary

JUL 2010

Assembling the AP and connecting the antenna

Chapter 2: AP Hardware Installation

Procedure 2-1 Assemble the AP and antenna for pole mounting (Continued)

4

Using a 5/16-18 x 3.5 hex pivot bolt, 5-16 split lock waster, 5/16 split flat

washer, smaller spacer (2.36 inches) and a 5/16 hex nut, connect the scissor
bracket to the top of the antenna.

See Detail A

5/16-8

Split Lock Washer

Outside

5/16-8

Hex Nut

5/16-8

Flat Washer

5/16-8 x 3.5in

Hex Pivot Bolt

Spacer (2.36in)

Detail A

Inverted Scissor Mount

5

Using the bracket with the shorter bar, attach the downtilt scissor bracket

pointing up (inverted scissor mount) to avoid physical interference between
the bracket and the radio housing. Connect the scissor bracket to the short
pipe bracket to the scissor bracket by attaching the 5/16-18 x 3.5 inch hex
pivot bolt, 5/16-18 flat washer, shorter spacer (2.24 inches) and the 5/16 –
18 hex nut.

Continued

«
...
36
37
38
39
40
...
»

Summary of Contents for PMP 320



















































































































































Reviews:

No comments

Related manuals for PMP 320

Univerge SV8100

Brand: NEC Pages: 44

Brand: Accelerated Pages: 10

Brand: Accelerated Pages: 4

Brand: LogLogic Pages: 30

Brand: Mercusys Pages: 35

APS6-400 Series

Brand: Eaton Pages: 114

Brand: Watchguard Pages: 40

Brand: Abocom Pages: 2

Brand: HELVAR Pages: 2

GSM7224v2 - Layer 2 Managed Gigabit Switch

Brand: NETGEAR Pages: 3

Brand: LevelOne Pages: 26

Brand: iGateWeb.com Pages: 6

Brand: Axis Pages: 98

Slideaway CL1008

Brand: ATEN Pages: 77

DEEP LEARNING PLUS

Brand: Concept Pro Pages: 28

Brand: Abocom Pages: 1

Brand: Planet Pages: 2

Brand: Dinstar Pages: 103

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands