Motorola PMP 320 Hardware Installation Download

Page: 39 / 146

PMP320HDW2v1

2-9

Preliminary

JUL 2010

PMP 320 Hardware Installation

Assembling the AP and connecting the antenna

Procedure 2-1 Assemble the AP and antenna for pole mounting (Continued)

See Detail A

NOTE

Use Shorter

Spacer (2.24in)

5/16-8

Hex Nut

Detail A

5/16-8

Flat Washer

5/16-8 x 3.5in

Hex Pivot Bolt

5/16-8

Split Lock Washer

Use a level (inclinometer) to tilt of the antenna when installing at
the site. The scissor bracket has degree markings from 0 to 15 on
the bracket, but it is recommended for accuracy to use a level.

Connect the radio to the antenna by sliding it into the captive space.

Radio

2X M6 Hex Nut
2X M6 Lock Washer
2X M6 Flat Washer

NOTE:

Slide Radio into

captive space of Antenna
First then secure with
mounting hardware

M6 Carriage Bolt

Antenna

Summary of Contents for PMP 320


















































































































































Search results

Summary of Contents for PMP 320

Reviews:

Related manuals for PMP 320

Brands by name

Popular brands

Motorola PMP 320, Hardware Installation

Search results

Summary of Contents for PMP 320

Reviews:

Related manuals for PMP 320

Brands by name

Popular brands